Yamaha 2100E Owners Manual - Page 20

SCSI ID Number, The ID number is set by attaching/detaching the shunts on the ID Select

Get Yamaha 2100E - CRW - CD-RW Drive PDF manuals and user guides View all Yamaha 2100E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Setup Procedures 1 SCSI ID Number Each of the SCSI devices connected to the computer is identified by its SCSI ID number. You need to assign a number from "0" to "7" for each SCSI device. Commonly, ID number "7" is reserved for the computer's SCSI card itself. Therefore, the CRW2100S drive can actually be assigned an ID number from "0" to "6." The ID number is set by attaching/detaching the shunts on the ID Select jumper switches according to the diagram shown below. SCSI ID 0 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI ID 1 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI ID 2 ID SELECT PARITY TERMINATOR 1 24 BLOCK SIZE SCSI ID 3 (Default) ID SELECT PARITY TERMINATOR 1 24 BLOCK SIZE SCSI ID 4 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI ID 5 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI ID 6 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE SCSI ID 7 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE n The SCSI ID number for each device on the chain must be unique. Make sure the CRW2100S drive's SCSI ID number is not the same as that of any other device on the chain. By factory default, the CRW2100S drive is assigned ID number "3" but this can be changed. n If the SCSI card supports SCAM and SCAM is turned "ON," a different ID number may be assigned if the SCSI ID number on the rear panel coincides with another SCSI device. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Setup Procedures
11
1
SCSI ID Number
Each of the SCSI devices connected to the computer is identified by its SCSI ID
number.
You need to assign a number from “0” to “7” for each SCSI device.
Commonly, ID number “7” is reserved for the computer’s SCSI card itself.
Therefore, the CRW2100S drive can actually be assigned an ID number from “0”
to “6.”
The ID number is set by attaching/detaching the shunts on the ID Select
jumper switches according to the diagram shown below.
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 24
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 24
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 24
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 24
1 24
1 24
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 24
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
1 24
SCSI ID 0
SCSI ID 1
SCSI ID 2
SCSI ID 3 (Default)
SCSI ID 4
SCSI ID 5
SCSI ID 6
SCSI ID 7
n
The SCSI ID number for each device on the chain must be unique.
Make sure the
CRW2100S drive’s SCSI ID number is not the same as that of any other device on the
chain.
By factory default, the CRW2100S drive is assigned ID number “3” but this can
be changed.
n
If the SCSI card supports SCAM and SCAM is turned “ON,” a different ID number may
be assigned if the SCSI ID number on the rear panel coincides with another SCSI device.