Yamaha DSP-E800 Owner's Manual - Page 14

Other connections, CENTER SPEAKERS terminals

Get Yamaha DSP-E800 PDF manuals and user guides View all Yamaha DSP-E800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

CONNECTIONS s Speaker cables Other connections 10 mm (3/8") 1 2 1 Remove approx. 10 mm (3/8") of insulation from each of the speaker cables. 2 Twist the exposed wires of the cable together to prevent short circuits. s Connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (-) 2 1 3 1 Unscrew the knob. 2 Insert one bare wire into the hole in the side of each terminal. 3 Tighten the knob to secure the wire. s Using this unit as a Dolby Digital or DTS decoder Connect the OUTPUT terminals (MAIN, REAR, CENTER and SUBWOOFER) of this unit to the EXTERNAL DECODER or 6 CHANNEL input terminals of the external amplifier. s Receiving the multi-channel signal from other equipment 1 Be sure to move the EXTERNAL DECODER/ MAIN IN switch to the EXTERNAL DECODER position before you turn on this unit. 2 Connect the OUTPUT terminal of the external amplifier to the 6CH INPUT terminals of this unit. 3 Press TAPE/MD MON / 6CH INPUT repeatedly (or 6CH INPUT once) until "6CH INPUT" appears on the display. • The signal on the main channel will be output to the MAIN OUTPUT terminals. • The overall volume level will be controlled by DSP- E800. s Using this unit as a power amplifier 1 Be sure to move the EXTERNAL DECODER/ MAIN IN switch to the MAIN IN position before you turn on this unit. 2 Press TAPE/MD MON / 6CH INPUT repeatedly (or 6CH INPUT once) until "6CH INPUT" appears on the display. • DSP-E800 is regarded as 3-channel power amplifier. The REAR L, the REAR R, and the CENTER terminals can be used for the connection. • The volume control of this unit will be bypassed. E-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
E-12
■
Speaker cables
1
Remove approx. 10 mm (3/8”) of insulation
from each of the speaker cables.
2
Twist the exposed wires of the cable together
to prevent short circuits.
■
Connecting to the REAR and
CENTER SPEAKERS terminals
1
Unscrew the knob.
2
Insert one bare wire into the hole in the side of
each terminal.
3
Tighten the knob to secure the wire.
CONNECTIONS
1
2
10 mm (3/8”)
2
3
1
Red: positive (+)
Black: negative (–)
Other connections
■
Using this unit as a Dolby Digital
or DTS decoder
Connect the OUTPUT terminals (MAIN, REAR, CENTER
and SUBWOOFER) of this unit to the EXTERNAL
DECODER or 6 CHANNEL input terminals of the external
amplifier.
■
Receiving the multi-channel signal
from other equipment
1
Be sure to move the EXTERNAL DECODER/
MAIN IN switch to the EXTERNAL DECODER
position before you turn on this unit.
2
Connect the OUTPUT terminal of the external
amplifier to the 6CH INPUT terminals of this
unit.
3
Press TAPE/MD MON / 6CH INPUT repeatedly
(or 6CH INPUT once) until “6CH INPUT”
appears on the display.
•
The signal on the main channel will be output to the
MAIN OUTPUT terminals.
•
The overall volume level will be controlled by DSP-
E800.
■
Using this unit as a power
amplifier
1
Be sure to move the EXTERNAL DECODER/
MAIN IN switch to the MAIN IN position before
you turn on this unit.
2
Press TAPE/MD MON / 6CH INPUT repeatedly
(or 6CH INPUT once) until “6CH INPUT”
appears on the display.
•
DSP-E800 is regarded as 3-channel power amplifier.
The REAR L, the REAR R, and the CENTER
terminals can be used for the connection.
•
The volume control of this unit will be bypassed.