Yamaha DSP-E800 Owner's Manual - Page 35

English, Basic Operation, Advanced Opera, Appendix, Introduction, Preparation, E-33

Get Yamaha DSP-E800 PDF manuals and user guides View all Yamaha DSP-E800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

INTRODUCTION PREPARATION TROUBLESHOOTING SYMPTOM No sound from the main speakers. No sound from the center speaker. No sound from the rear speakers. No sound from the subwoofer. A "humming" sound can be heard. The volume level cannot be increased, or the sound is distorted. The sound effect cannot be recorded. The DVD/LD, D-TV or CBL/SAT source cannot be recorded by tape deck, MD recorder or VCR connected to this unit. Adjusting this unit by using SET MENU, TIME/ LEVEL or TEST cannot be performed. CAUSE REMEDY Incorrect output connection to the external amplifier. The external amplifier connected to this unit is turned off. The sound output level of the center speaker is set to minimum. "CENTER SP" on the SET MENU is set to the NONE position. Incorrect DSP program is selected. The source encoded with Dolby Digital or DTS does not have a center channel signal. The output level of the rear speakers is set to minimum. A monaural source is being played with the PRO LOGIC/Normal or PRO LOGIC/ENHANCED program. "BASS OUT" on the SET MENU is set to the SW or MAIN position when playing a 2-channel source. The source does not contain low bass signals (below 90 Hz). Incorrect cable connections. The component connected to the TAPE/MD OUT (REC) terminals of this unit is in the standby mode. It is not possible to record the sound effect by a tape deck or MD recorder connected to the TAPE/MD OUT (REC) terminals of this unit. The DVD/LD player, TV/digital TV or cable TV/satellite tuner is connected to the unit only through the digital terminals. Connect the external amplifier correctly. Turn on the power to the external amplifier. Raise the level of the center speaker. Select the LRG or SML position. Select the appropriate program. Raise the output level of the rear speakers. Select another DSP program suitable for the monaural source. Select the BOTH position. Firmly connect the audio plugs. If the problem persists, the cables may be defective. Turn on the power to the component. Make additional connections between the analog terminals. "MEM. GUARD" on the SET MENU is set to the ON position. Set "MEM. GUARD" to the OFF position. Refer to page 11, 12 11, 12 29 26 22, 23, 24 - 29 24 26 - 9, 10 - 21 10 28 BASIC OPERATION ADVANCED OPERATION APPENDIX English E-33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
E-33
English
BASIC OPERATION
ADVANCED OPERA
TION
APPENDIX
INTRODUCTION
PREPARATION
TROUBLESHOOTING
SYMPTOM
No sound from the main
speakers.
No sound from the
center speaker.
No sound from the rear
speakers.
No sound from the
subwoofer.
A “humming” sound can
be heard.
The volume level cannot
be increased, or the
sound is distorted.
The sound effect cannot
be recorded.
The DVD/LD, D-TV or
CBL/SAT source cannot
be recorded by tape
deck, MD recorder or
VCR connected to this
unit.
Adjusting this unit by
using SET MENU, TIME/
LEVEL or TEST cannot
be performed.
CAUSE
Incorrect output connection to the external
amplifier.
The external amplifier connected to this unit is
turned off.
The sound output level of the center speaker is
set to minimum.
“CENTER SP” on the SET MENU is set to the
NONE position.
Incorrect DSP program is selected.
The source encoded with Dolby Digital or DTS
does not have a center channel signal.
The output level of the rear speakers is set to
minimum.
A monaural source is being played with the PRO
LOGIC/Normal or PRO LOGIC/ENHANCED
program.
“BASS OUT” on the SET MENU is set to the
SW or MAIN position when playing a 2-channel
source.
The source does not contain low bass signals
(below 90 Hz).
Incorrect cable connections.
The component connected to the TAPE/MD
OUT (REC) terminals of this unit is in the
standby mode.
It is not possible to record the sound effect by a
tape deck or MD recorder connected to the
TAPE/MD OUT (REC) terminals of this unit.
The DVD/LD player, TV/digital TV or cable
TV/satellite tuner is connected to the unit only
through the digital terminals.
“MEM. GUARD” on the SET MENU is set to
the ON position.
REMEDY
Connect the external amplifier correctly.
Turn on the power to the external amplifier.
Raise the level of the center speaker.
Select the LRG or SML position.
Select the appropriate program.
Raise the output level of the rear speakers.
Select another DSP program suitable for the
monaural source.
Select the BOTH position.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
Turn on the power to the component.
Make additional connections between the analog
terminals.
Set “MEM. GUARD” to the OFF position.
Refer to
page
11, 12
11, 12
29
26
22, 23, 24
—
29
24
26
—
9, 10
—
21
10
28