Yamaha IM8-24 Owner's Manual - Page 25

English Español Français Deutsch Specifications General Specifications Input HPF Input Equalization (+15, -15dB maximum) Turn over/roll-off frequency of shelving: 3dB below maximum variable level. LAMP IM8-40: 3 pcs, IM8-32/24: 2pcs Signal Indicator LED Level Meter USB Audio Compressor Dimensions Net Weight MONO CH INPUT* MONO CH INPUT* ST CH INPUT MONO CH INPUT* ST CH INPUT 1-4 INSERT OUT GROUP OUT, AUX SEND, MONO OUT Post STEREO OUT fader Pre MONITOR control USB IN/OUT MONO CH INPUT* 80 Hz, 12 dB/oct HIGH: 10 kHz (shelving) Hi-MID: 400 Hz-8 kHz (peaking) LO-MID: 80 Hz-1.6 kHz (peaking) LOW: 100 Hz (shelving) HIGH: 10 kHz (shelving) Hi-MID: 3 kHz (peaking) LO-MID: 800 Hz (peaking) LOW: 100 Hz (shelving) XLR-4-31 type, The LAMP voltage is 12 V DC between 3 and 4 pins of XLR-4-31 connectors. Each lamp can use 5 W max. 3 points LED meter (PEAK, 0, -20 dB) PEAK lights if the signal reaches 3dB below the clipping level. 4x12 points LED meters (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) Sampling Frequency = 44.1/48 kHz (depending on the PC application) Control x 1 (gain/threshold/ratio) Height: 219 mm, Depth: 739 mm, Width: 1716 mm (IM8-40), 1471.5 mm (IM8-32), 1227 mm (IM8-24) 51.5 kg (IM8-40), 44.4 kg (IM8-32), 37.8 kg (IM8-24) All faders are nominal when measured. (The nominal position is 10 dB lower than the maximum position.) Output impedance of signal generator: 150 ohms * IM8-40: 1-40, IM8-32: 1-32, IM8-24: 1-24 Analog Input Specifications Input Connectors INPUT A (MONO CHs) IM8-40: 1-40 IM8-32: 1-32 IM8-40: 1-24 INPUT B (MONO CHs) IM8-40: 1-40 IM8-32: 1-32 IM8-40: 1-24 INPUT A/B (ST CHs) INSERT IN (MONO CHs) IM8-40: 1-40 IM8-32: 1-32 IM8-40: 1-24 INSERT IN (AUX, GROUP, STEREO, MONO) AUX RETURN 1-4 2TR IN L/R TALKBACK MIC IN PAD 0 26 dB 0 26 dB - - - GAIN -60 dB -16 dB -34 dB +10 dB -60 dB -16 dB -34 dB +10 dB -34 dB +10 dB - - - - Input Impedance 3 kΩ 10 kΩ 10 kΩ 10 kΩ 10 kΩ 10 kΩ 10 kΩ 10 kΩ Appropriate Impedance 50-600 Ω Mics 600 Ω Mics/Lines 600 Ω Lines 600 Ω Lines 600 Ω Lines 600 Ω Lines 600 Ω Lines 600 Ω Lines Sensitivity* Nominal Level -80 dBu (0.078 mV) -36 dBu (12.3 mV) -54 dBu (1.55 mV) -10 dBu (245 mV) -80 dBu (0.078 mV) -36 dBu (12.3 mV) -54 dBu (1.55 mV) -10 dBu (245 mV) -54 dBu (1.55 mV) -10 dBu (245 mV) -60 dBu (0.775 mV) -16 dBu (123 mV) -34 dBu (15.5 mV) +10 dBu (2.45 V) -60 dBu (0.775 mV) -16 dBu (123 mV) -34 dBu (15.5 mV) +10 dBu (2.45 V) -34 dBu (15.5 mV) +10 dBu (2.45 V) -20 dBu (77.5 mV) 0 dBu (0.775 V) -10 dBu (77.5 mV) 0 dBu (0.775 V) -12 dBu (195 mV) +4 dBu (1.23 V) -26 dBV (50.1 mV) -10 dBV (0.316 V) -66 dBu (0.389 mV) -50 dBu (2.45 mV) Max. before clipping Connector Specifications -40 dBu (7.75 mV) XLR-3-31 type (balanced [1=GND, +4 dBu (1.23 V) 2=HOT, 3=COLD]) -14 dBu (155 mV) +30 dBu (24.5 V) -40 dBu (7.75m V) TRS phone jack (balanced [Tip = +4 dBu (1.23 V) HOT, Ring = COLD, Sleeve = GND]) -14 dBu (155 mV) +30 dBu (24.5 V) -14 dBu (155 mV) Phone jack (unbalanced) +30 dBu (24.5 V) RCA pin jack TRS phone jack (unbalanced [Tip +20 dBu (7.75 V) = Out, Ring = In, Sleeve = GND]) +10 dBu (2.45 V) TRS phone jack (unbalanced [Tip = Out, Ring = In, Sleeve = GND]) +24 dBu (12.3 V) Phone jack (unbalanced) RCA pin jack +10 dBV (3.16 V) 3.5 DIA stereo phone jack -30 dBu (24.5 mV) XLR-3-31 type (unbalanced) Where 0 dBu = 0.775 Vrms and 0 dBV = 1 Vrms * Sensitivity is the lowest level that will produce an output of +4dB (1.23 V), or the nominal output level when the unit is set to the maximum level. (All faders and level controls are at their maximum positions.) Italiano Owner's Manual 167