Yamaha MCP1 MCP1 Installation Manual - Page 13

Setting the UNIT ID

Get Yamaha MCP1 PDF manuals and user guides View all Yamaha MCP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Setting the UNIT ID Set the MCP1's UNIT ID. Operate the switches with bare hands. If you attempt to operate them while wearing gloves, they will not work correctly. 1. Long-touch (two seconds or longer) the home switch. Move to the utility page. 2. Touch the [Settings] switch (R1). Move to the settings page. After synchronizing with MTX-MRX Editor, it will be necessary to enter the PIN code. NOTE If you have forgotten the PIN code, use MTX-MRX Editor to specify it again. 13 2 5, 7 3. Touch the [IP Setting] switch (L1). Specify whether the IP address is determined by the UNIT ID or by MTX-MRX Editor (PC). 6 5, 7 4. Make sure that "IP Setting" is set to [UNIT ID]. If it is set to [PC], touch the L1/2/3 switches at the left to set it to [UNIT ID]. If you are using a subnet other than 192.168.0.x, set this to [PC] and make the setting in MTXMRX Editor. 5. Touch the return switch. A confirmation screen appears; select Yes. The setting is confirmed as the UNIT ID, and the MCP1 automatically restarts. 6. Touch the [Unit ID] switch (L2). Set the MCP1's UNIT ID. Set the ID so that it does not conflict with the UNIT ID of another unit within the same network. Touching an L1/2/3 switch decreases the number; touching an R1/2/3 switch increases the number. 7. When you've set the UNIT ID, touch the return switch. A confirmation screen appears; select Yes. The UNIT ID is confirmed, and the MCP1 automatically restarts. MCP1 Installation Manual 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
13
MCP1 Installation Man
u
al
Setting the UNIT ID
Set the MCP1’s UNIT ID.
Operate the s
w
itches
w
ith
b
are hands. If yo
u
attempt to operate them
w
hile
w
earing glo
v
es,
they
w
ill not
w
ork correctly.
1.
Long-touch (two seconds or longer) the
home switch.
Mo
v
e to the
u
tility page.
2.
Touch the [Settings] switch (R1).
Mo
v
e to the settings page. After synchronizing
w
ith MTX-MRX Editor, it
w
ill
b
e necessary to
enter the PIN code.
3.
Touch the [IP Setting] switch (L1).
Specify
w
hether the IP address is determined
b
y
the UNIT ID or
b
y MTX-MRX Editor (PC).
4.
Make sure that “IP Setting” is set to [UNIT
ID].
If it is set to [PC], to
u
ch the L1/2/3 s
w
itches at
the left to set it to [UNIT ID].
If yo
u
are
u
sing a s
ub
net other than 192.16
8
.0.x,
set this to [PC] and make the setting in MTX-
MRX Editor.
5.
Touch the return switch.
A confirmation screen appears; select Yes. The setting is confirmed as the UNIT ID, and
the MCP1 a
u
tomatically restarts.
6.
Touch the [Unit ID] switch (L2).
Set the MCP1’s UNIT ID.
Set the ID so that it does not conflict
w
ith the UNIT ID of another
u
nit
w
ithin the same net-
w
ork.
To
u
ching an L1/2/3 s
w
itch decreases the n
u
m
b
er; to
u
ching an R1/2/3 s
w
itch increases the
n
u
m
b
er.
7.
When you’ve set the UNIT ID, touch the return switch.
A confirmation screen appears; select Yes. The UNIT ID is confirmed, and the MCP1 a
u
to-
matically restarts.
NOTE
If yo
u
ha
v
e forgotten the PIN code,
u
se MTX-MRX
Editor to specify it again.
3
2
6
5, 7
1
5, 7