Yamaha RMio64-D RMio64-D Owners Manual [English] - Page 14

Signal Flow

Get Yamaha RMio64-D PDF manuals and user guides View all Yamaha RMio64-D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Dante Network Settings and Audio Routing With the Dante network, you can route the audio input and output of multiple Dante devices in any way you like. This requires you to set which channel signals are sent to which inputs. The routing for connecting MADI with the Dante network is fixed on the RMio64-D. Therefore, any changes in routing are made in the Dante network. Use Dante Controller to configure the audio routing of the Dante network. You can download Dante Controller from the following website: http://www.yamahaproaudio.com/ Refer to the Dante Controller owner's manual (available from the same website) for details about Dante Controller. Selecting MADI Input Rate Use the MADI [INPUT RATE] 1Fs/2Fs/4Fs keys on the front panel to select the MADI input rate. For example, for a MADI input rate of 192 kHz (4x 48 kHz), confirm that the MADI [INPUT RATE Fs 48kHz] indicator is on, and then select [4Fs]. If no valid MADI input signal is detected, both indicators remain off. Panel Lock You can lock the panel to prevent unintended changes and operations. While the lock is engaged, all controllers on the front panel are inoperable. To engage the lock, press and hold the MADI [STATUS] INPUT/OUTPUT key for at least 3 seconds. All front panel indicators (except the power indicator) flash, indicating all controllers are locked. To disengage the lock, press and hold the MADI [STATUS] INPUT/OUTPUT key for at least 3 seconds. Signal Flow Dante to MADI The Dante input signal is output from the MADI [COAXIAL OUT] connector and the [OPTICAL OUT] connector. MADI to Dante The MADI input signal is output from the Dante [PRIMARY] and [SECONDARY] connectors. MADI Split A signal that is input via coaxial or optical connector can be looped back via the other connector. When doing so, the signal also goes to the Dante network.  Settings • To use a MADI split, turn on MADI DIP switch 3 (DOWN). • To loop back the input signal from the MADI [COAXIAL IN] connector to the MADI [OPTICAL OUT] connector, turn on MADI DIP switch 1 (DOWN). 3 seconds NOTE Even if the front panel is locked, you can use remote control to make changes to the settings. For the latest information about remote control compatible devices, refer to the Yamaha Pro Audio website: http://www.yamahaproaudio.com/ 14 RMio64-D Owner's Manual • To loop back the input signal from the MADI [OPTICAL IN] connector to the MADI [COAXIAL OUT] connector, turn off MADI DIP switch 1 (UP). NOTE Make sure to change the settings of the DIP switches while the power to the unit is turned off; otherwise, the ID setting will not be effective.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
RMio64-D Owner’s Manual
14
Dante Network Settings and
Audio Routing
With the Dante network, you can route the audio input
and output of multiple Dante devices in any way you like.
This requires you to set which channel signals are sent
to which inputs. The routing for connecting MADI with
the Dante network is fixed on the RMio64-D. Therefore,
any changes in routing are made in the Dante network.
Use Dante Controller to configure the audio routing of
the Dante network.
You can download Dante Controller from the following
website:
Refer to the Dante Controller owner’s manual (available
from the same website) for details about Dante
Controller.
Selecting MADI Input Rate
Use the MADI [INPUT RATE] 1Fs/2Fs/4Fs keys on the
front panel to select the MADI input rate.
For example, for a MADI input rate of 192 kHz (4x 48
kHz), confirm that the MADI [INPUT RATE Fs 48kHz]
indicator is on, and then select [4Fs]. If no valid MADI
input signal is detected, both indicators remain off.
Panel Lock
You can lock the panel to prevent unintended changes
and operations. While the lock is engaged, all controllers
on the front panel are inoperable. To engage the lock,
press and hold the MADI [STATUS] INPUT/OUTPUT key
for at least 3 seconds. All front panel indicators (except
the power indicator) flash, indicating all controllers are
locked. To disengage the lock, press and hold the MADI
[STATUS] INPUT/OUTPUT key for at least 3 seconds.
NOTE
Even if the front panel is locked, you can use remote control to
make changes to the settings.
For the latest information about remote control compatible
devices, refer to the Yamaha Pro Audio website:
Signal Flow
Dante to MADI
The Dante input signal is output from the MADI
[COAXIAL OUT] connector and the [OPTICAL OUT]
connector.
MADI to Dante
The MADI input signal is output from the Dante
[PRIMARY] and [SECONDARY] connectors.
MADI Split
A signal that is input via coaxial or optical connector can
be looped back via the other connector. When doing so,
the signal also goes to the Dante network.
Settings
•
To use a MADI split, turn on MADI DIP switch 3
(DOWN).
•
To loop back the input signal from the MADI [COAXIAL
IN] connector to the MADI [OPTICAL OUT] connector,
turn on MADI DIP switch 1 (DOWN).
•
To loop back the input signal from the MADI [OPTICAL
IN] connector to the MADI [COAXIAL OUT] connector,
turn off MADI DIP switch 1 (UP).
NOTE
Make sure to change the settings of the DIP switches while the
power to the unit is turned off; otherwise, the ID setting will not
be effective.
3 seconds