Yamaha RMio64-D RMio64-D Owners Manual [English] - Page 18

Routing / Patching, Remote Control, Other Issues, Restoring Factory Settings

Get Yamaha RMio64-D PDF manuals and user guides View all Yamaha RMio64-D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Routing / Patching A mixer is not receiving an input signal from the RMio64-D • Is the patch of the Dante network set up correctly by Dante Controller? • Is the patch setting in the mixer set to use the Dante Controller? • Is the word clock setting in the mixer set to correspond to the Dante network? How can the Dante input and output signals be patched? Use Dante Controller to configure the audio routing (patching) of the Dante network. For details, refer to the Dante Controller User Guide available on the website. http://www.yamahaproaudio.com/ Is it possible to input a signal from two RMio64-D units to one channel of the mixer? Unlike with output, input can receive only the signal of one channel. Is it possible to receive the input signal from RMio64-D by a separate mixer? It can be configured using the Dante Controller. For details, refer to the Dante Controller User Guide available on the website. http://www.yamahaproaudio.com/ Remote Control I want to change the RMio64-D settings from the mixer I want to know the devices that can remotely configure the RMio64-D For details on RMio64-D remote control, refer to the following website. http://www.yamahaproaudio.com/ Other Issues What is the latency of the Dante network? The latency value can be set by Dante Controller or some mixers. For details, refer to the manuals for each product. An internal error message such as "firmware mismatch" is displayed on the device connected to the RMio64-D. Make sure that each device has a compatible version. For details, refer to the firmware compatibility information available on the website. http://www.yamahaproaudio.com/ Restoring Factory Settings Perform the following steps to restore the factory settings. 1. Turn the unit off. 2. Turn on Dante DIP switch 2 (DOWN), and turn the unit on. All front panel indicators (except the power indicator) flash, indicating all parameters have been restored to the factory settings. 3. Turn the unit off. 4. Turn off Dante DIP switch 2 (UP). 5. Turn the unit on again. 18 RMio64-D Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
RMio64-D Owner’s Manual
18
Routing / Patching
A mixer is not receiving an input signal
from the RMio64-D
•
Is the patch of the Dante network set up correctly by
Dante Controller?
•
Is the patch setting in the mixer set to use the Dante
Controller?
•
Is the word clock setting in the mixer set to correspond
to the Dante network?
How can the Dante input and output
signals be patched?
Use Dante Controller to configure the audio routing
(patching) of the Dante network. For details, refer to the
Dante Controller User Guide available on the website.
Is it possible to input a signal from two
RMio64-D units to one channel of the
mixer?
Unlike with output, input can receive only the signal of
one channel.
Is it possible to receive the input signal
from RMio64-D by a separate mixer?
It can be configured using the Dante Controller. For
details, refer to the Dante Controller User Guide
available on the website.
Remote Control
I want to change the RMio64-D settings
from the mixer
I want to know the devices that can
remotely configure the RMio64-D
For details on RMio64-D remote control, refer to the
following website.
Other Issues
What is the latency of the Dante
network?
The latency value can be set by Dante Controller or
some mixers. For details, refer to the manuals for each
product.
An internal error message such as
“firmware mismatch” is displayed on
the device connected to the RMio64-D.
Make sure that each device has a compatible version.
For details, refer to the firmware compatibility information
available on the website.
Restoring Factory Settings
Perform the following steps to restore the factory
settings.
1.
Turn the unit off.
2.
Turn on Dante DIP switch 2 (DOWN), and
turn the unit on.
All front panel indicators (except the power
indicator) flash, indicating all parameters have
been restored to the factory settings.
3.
Turn the unit off.
4.
Turn off Dante DIP switch 2 (UP).
5.
Turn the unit on again.