Yamaha RX-V683 RX-V683 Quick Start Guide - Page 17

YPAO Volume and press ENTER.

Get Yamaha RX-V683 PDF manuals and user guides View all Yamaha RX-V683 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

1 Turn on the subwoofer and set the volume to half. If the crossover frequency is adjustable, set it to maximum. VOLUME CROSSOVER/ HIGH CUT 3 Use the cursor keys to select "Measure" and press ENTER. The measurement will start in 10 seconds. It takes about 3 minutes to measure. The screen below appears on the TV when the measurement finishes. MIN MAX MIN MAX 2 Place the YPAO microphone at your listening position and connect it to the YPAO MIC jack on the front panel. The screen below appears on the TV. Note Place the YPAO microphone at your listening position (same height as your ears). We recommend the use of a tripod as a microphone stand. You can use the tripod screws to stabilize the microphone. Note If an error message (such as E-1) or warning message (such as W-2) appears, see "Error messages" or "Warning messages" under "Optimizing the speaker settings automatically (YPAO)" in the Owner's Manual. 4 Use the cursor keys to select "Save/Cancel" and press ENTER. 5 Use the cursor keys to select "SAVE" and press ENTER. 6 Use the cursor keys to select "YES" to enable YPAO Volume and press ENTER. 7 Disconnect the YPAO microphone from the unit. This completes optimization of the speaker settings. En 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
En
17
1
Turn on the subwoofer and set the volume to half.
If the crossover frequency is adjustable, set it to maximum.
2
Place the YPAO microphone at your listening
position and connect it to the YPAO MIC jack on
the front panel.
The screen below appears on the TV.
Note
Place the YPAO microphone at your listening position (same height as your ears).
We recommend the use of a tripod as a microphone stand. You can use the tripod
screws to stabilize the microphone.
3
Use the cursor keys to select “Measure” and press
ENTER.
The measurement will start in 10 seconds.
It takes about 3 minutes to measure.
The screen below appears on the TV when the measurement finishes.
Note
If an error message (such as E-1) or warning message (such as W-2) appears,
see “Error messages” or “Warning messages” under “Optimizing the speaker
settings automatically (YPAO)” in the Owner’s Manual.
4
Use the cursor keys to select “Save/Cancel” and
press ENTER.
5
Use the cursor keys to select “SAVE” and press
ENTER.
6
Use the cursor keys to select “YES” to enable
YPAO Volume and press ENTER.
7
Disconnect the YPAO microphone from the unit.
This completes optimization of the speaker settings.
VOLUME
CROSSOVER/
HIGH CUT
MIN
MAX
MIN
MAX