Yamaha YSP-2200 Owners Manual - Page 49

AUTO LIP SYNC is set - tv remote

Get Yamaha YSP-2200 PDF manuals and user guides
UPC - 027108937847
View all Yamaha YSP-2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

PREPARATION CONNECTION/ INITIAL SETTINGS PLAYBACK Troubleshooting Problem Cause Remedy No sound from the subwoofer. The image is not displayed on TV screen. Menu screen of this unit is not displayed. A digital or highfrequency equipment produces noises. The system settings change automatically. The HDMI control function does not work properly. The automatic lipsync is not effective even "AUTO LIP SYNC" is set to "ON". "Not Available" appears on the front panel display after key operation. The subwoofer is not connected properly. The level of subwoofer is low. HDMI cable is not securely connected. VIDEO OUTPUT jacks of this unit and TV are not connected. The input switch of TV is not set correctly. The unit may be placed close to digital equipment or high-frequency equipment. When "HDMI CONTROL" is set to "ON", operations of the TV (for example, changing channels, etc.) may change the system settings, such as the surround mode. "HDMI CONTROL" is set to "OFF". The HDMI control function is disabled on your TV. The number of the connected HDMI components is over the limit. The TV does not support the automatic lipsync. The key is unable to function in the current condition. Check if the subwoofer is connected properly. Increase the subwoofer level with SUBWOOFER + key. Connect them with an HDMI connection or a digital connection. Connect the jacks with video pin cable (supplied). Switch the input source for your TV. Leave these equipments from the unit. Set "HDMI CONTROL" to "OFF" or set the system again by using its remote control. Set "HDMI CONTROL" to "ON". Refer to the manual supplied with your TV and check the setting. Disconnect some of the HDMI components. Set "AUTO LIP SYNC" to "OFF" and then manually adjust the audio output delay. See page 13 26 14, 15 14 - - 43 43 - - 40 Remote control Problem The remote control does not work and/or function properly. Cause Remedy Wrong distance or angle. Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. The batteries are weak. The remote control functions within a maximum range of 6 m (20 ft) and no more than 30 degrees off-axis from the front panel. Reposition this unit. Replace all batteries. See page 13 - 13 SETTINGS TROUBLESHOOTING APPENDIX 47 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Troubleshooting
47
En
PREPARATION
CONNECTION/
INITIAL SETTINGS
PLAYBACK
SETTINGS
TROUBLESHOOTING
APPENDIX
No sound from the
subwoofer.
The subwoofer is not connected properly.
Check if the subwoofer is connected properly.
13
The level of subwoofer is low.
Increase the subwoofer level with SUBWOOFER +
key.
26
The image is not
displayed on TV screen.
HDMI cable is not securely connected.
Connect them with an HDMI connection or a
digital connection.
14, 15
Menu screen of this unit
is not displayed.
VIDEO OUTPUT jacks of this unit and TV
are not connected.
Connect the jacks with video pin cable (supplied).
14
The input switch of TV is not set correctly.
Switch the input source for your TV.
–
A digital or high-
frequency equipment
produces noises.
The unit may be placed close to digital
equipment or high-frequency equipment.
Leave these equipments from the unit.
–
The system settings
change automatically.
When “HDMI CONTROL” is set to “ON”,
operations of the TV (for example,
changing channels, etc.) may change the
system settings, such as the surround mode.
Set “HDMI CONTROL” to “OFF” or set the
system again by using its remote control.
43
The HDMI control
function does not work
properly.
“HDMI CONTROL” is set to “OFF”.
Set “HDMI CONTROL” to “ON”.
43
The HDMI control function is disabled on
your TV.
Refer to the manual supplied with your TV and
check the setting.
–
The number of the connected HDMI
components is over the limit.
Disconnect some of the HDMI components.
–
The automatic lipsync
is not effective even
“AUTO LIP SYNC” is set
to “ON”.
The TV does not support the automatic
lipsync.
Set “AUTO LIP SYNC” to “OFF” and then
manually adjust the audio output delay.
40
“Not Available” appears
on the front panel
display after key
operation.
The key is unable to function in the current
condition.
Remote control
Problem
Cause
Remedy
See
page
The remote control
does not work and/or
function properly.
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees
off-axis from the front panel.
13
Direct sunlight or lighting (from an inverter
type of fluorescent lamp, etc.) is striking
the remote control sensor of this unit.
Reposition this unit.
–
The batteries are weak.
Replace all batteries.
13
Problem
Cause
Remedy
See
page