Zanussi ZBB24430SA Product Manaul - Page 8

Problem, Possible cause, Solution - manual

Get Zanussi ZBB24430SA PDF manuals and user guides View all Zanussi ZBB24430SA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

What to do if... Warning! Before troubleshooting, disconnect the mains plug from the mains socket. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual. Important! There are some sounds during normal use (compressor, refrigerant circulation). Problem The appliance does not operate. The lamp does not operate. The lamp does not work. The compressor operates continually. Water flows on the rear plate of the refrigerator. Water flows into the refrigerator. Water flows on the ground. The temperature in the appliance is too low. The temperature in the appliance is too high. Possible cause The appliance is switched off. The mains plug is not connected to the mains socket correctly. The appliance has no power. There is no voltage in the mains socket. The lamp is in stand-by. The lamp is defective. The temperature is not set correctly. The door is not closed correctly. The door has been opened too frequently. The product temperature is too high. The room temperature is too high. During the automatic defrosting process, frost defrosts on the rear plate. The water outlet is clogged. Products prevent that water flows into the water collector. The melting water outlet does not flow in the evaporative tray above the compressor. The temperature regulator is not set correctly. The temperature regulator is not set correctly. The door is not closed correctly. The product temperature is too high. Solution Switch on the appliance. Connect the mains plug to the mains socket correctly. Connect a different electrical appliance to the mains socket. Contact a qualified electrician. Close and open the door. Refer to "Replacing the lamp". Set a higher temperature. Refer to "Closing the door". Do not keep the door open longer than necessary. Let the product temperature decrease to room temperature before storage. Decrease the room temperature. This is correct. Clean the water outlet. Make sure that products do not touch the rear plate. Attach the melting water outlet to the evaporative tray. Set a higher temperature. Set a lower temperature. Refer to "Closing the door". Let the product temperature decrease to room temperature before storage. 8 www.zanussi.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
What to do if…
Warning!
Before troubleshooting, disconnect the
mains plug from the mains socket.
Only a qualified electrician or competent person must do
the troubleshooting that is not in this manual.
Important!
There are some sounds during normal use
(compressor, refrigerant circulation).
Problem
Possible cause
Solution
The appliance does not operate.
The lamp does not operate.
The appliance is switched off.
Switch on the appliance.
The mains plug is not connected to the
mains socket correctly.
Connect the mains plug to the mains
socket correctly.
The appliance has no power. There is
no voltage in the mains socket.
Connect a different electrical appliance
to the mains socket.
Contact a qualified electrician.
The lamp does not work.
The lamp is in stand-by.
Close and open the door.
The lamp is defective.
Refer to "Replacing the lamp".
The compressor operates contin-
ually.
The temperature is not set correctly.
Set a higher temperature.
The door is not closed correctly.
Refer to "Closing the door".
The door has been opened too fre-
quently.
Do not keep the door open longer than
necessary.
The product temperature is too high.
Let the product temperature decrease to
room temperature before storage.
The room temperature is too high.
Decrease the room temperature.
Water flows on the rear plate of
the refrigerator.
During the automatic defrosting proc-
ess, frost defrosts on the rear plate.
This is correct.
Water flows into the refrigerator.
The water outlet is clogged.
Clean the water outlet.
Products prevent that water flows into
the water collector.
Make sure that products do not touch
the rear plate.
Water flows on the ground.
The melting water outlet does not flow
in the evaporative tray above the com-
pressor.
Attach the melting water outlet to the
evaporative tray.
The temperature in the appliance
is too low.
The temperature regulator is not set
correctly.
Set a higher temperature.
The temperature in the appliance
is too high.
The temperature regulator is not set
correctly.
Set a lower temperature.
The door is not closed correctly.
Refer to "Closing the door".
The product temperature is too high.
Let the product temperature decrease to
room temperature before storage.
8
www.zanussi.com