Zanussi ZDC68560W Product Manaul - Page 12

Cleaning and maintenance - parts

Get Zanussi ZDC68560W PDF manuals and user guides View all Zanussi ZDC68560W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

The programme can no longer be changed directly once the programme has started. If nevertheless there is an attempt to change the programme on the pro- gramme knob, the programme progress display and the maintenance indicators flash. If an option button (exclud- ing the BUZZER button) is pressed, appears on the display. The drying programme is not however affec- ted by this (laundry protection). Drying cycle complete / removing laundry Once the drying cycle is complete, the display shows the anti-crease icon and flashing as well as warning lamps: FILTER and TANK . If the BUZZER button has been pressed, an acoustic signal sounds intermittently for about one minute. The drying cycles (except from the WOOL programme) are automatically followed by an anticrease phase which lasts around 30 minutes. The drum Cleaning and maintenance rotates at intervals during this phase. This keeps the laundry loose and free of creases. The laundry can be removed at any time during the anti-crease phase. (The laundry should be taken out towards the end of the anti-crease phase at the latest to prevent creases from forming.) 1. Open door. 2. Before removing the laundry, remove fluff from the micro-fine filter. It is best to use a damp hand for this purpose. (See "Cleaning and maintenance" chapter.) 3. Remove laundry. 4. Turn the programme selector to off. 5. Close the door. After each use • Clean the filters. • Empty the water reservoir. Cleaning lint filters To ensure that the appliance works perfectly, the lint filters in the door and in front of the drum must be cleaned after every drying cycle. Caution! Important. Never operate the dryer without the lint filter or with a damaged or blocked lint filter. 1. Open loading door 2. After a period of time, a patina due to detergent residue on laundry forms on the filters. Then clean the filters with warm water using a brush. Remove the filter from the door pulling it out. 3. Use a damp hand to 4. Remove fluff from lint clean the micro- fine filter, filter, preferably using a which is built into the low- damp hand for this pur- er part of the loading aper- pose. ture. Replace the filter. Cleaning heat exchanger Clean the condenser when light Condenser comes on. The condenser is situated at the lower part of the cabinet behind a small door. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
The programme can no longer be changed directly
once the programme has started. If nevertheless
there is an attempt to change the programme on the pro-
gramme knob, the programme progress display and the
maintenance indicators flash. If an option button (exclud-
ing the
BUZZER button) is pressed,
appears on
the display. The drying programme is not however affec-
ted by this (laundry protection).
Drying cycle complete / removing laundry
Once the drying cycle is complete, the display shows the
anti-crease icon and flashing as well as warning
lamps: FILTER and TANK . If the
BUZZER button has
been pressed, an acoustic signal sounds intermittently for
about one minute.
The drying cycles (except from the WOOL pro-
gramme) are automatically followed by an anti-
crease phase which lasts around 30 minutes. The drum
rotates at intervals during this phase. This keeps the laun-
dry loose and free of creases. The laundry can be removed
at any time during the anti-crease phase. (The laundry
should be taken out towards the end of the anti-crease
phase at the latest to prevent creases from forming.)
1.
Open door.
2.
Before removing the laundry, remove fluff from the
micro-fine filter. It is best to use a damp hand for
this purpose. (See “Cleaning and maintenance”
chapter.)
3.
Remove laundry.
4.
Turn the programme selector to
off.
5.
Close the door.
After each use
•
Clean the filters.
•
Empty the water reservoir.
Cleaning and maintenance
Cleaning lint filters
To ensure that the appliance works perfectly, the lint filters
in the door and in front of the drum must be cleaned after
every drying cycle.
Caution!
Important. Never operate the dryer without
the lint filter or with a damaged or blocked lint filter.
1. Open loading door
2. After a period of time, a
patina due to detergent
residue on laundry forms
on the filters. Then clean
the filters with warm water
using a brush. Remove the
filter from the door pulling
it out.
3. Use a damp hand to
clean the micro- fine filter,
which is built into the low-
er part of the loading aper-
ture.
4. Remove fluff from lint
filter, preferably using a
damp hand for this pur-
pose.
Replace the filter.
Cleaning heat exchanger
Clean the condenser when light
Condenser
comes on.
The condenser is situated at the lower part of the cabinet
behind a small door.
12