Zanussi ZDC68560W Product Manaul - Page 14

Troubleshooting by yourself

Get Zanussi ZDC68560W PDF manuals and user guides View all Zanussi ZDC68560W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

What to do if ... Troubleshooting by yourself Problem1) Possible cause Remedy Dryer does not work. Dryer not connected to mains supply. Loading door opened. Plug in at mains socket. Check fuse in fuse box (domestic installation). Close loading door The START PAUSE button not pressed. Press the START PAUSE button. Incorrect programme set. Set suitable programme. 2) Fluff filters clogged. Clean fluff filters. 3) Unsatisfactory drying results. Heat exchanger clogged. Max. loading exceeded. Covered ventilation grill. Clean heat exchanger. 3) Respect max. loading volume. Uncover ventilation grill in base area. Residue inside the drum. Clean the drum inside. High water hardness. Set suitable water hardness4). Loading door does not close Filters not locked in place. Install fine filter and/or snap course filter into place. Err (Error) on the LCD.5) Attempt to change parameters after start of the programme. Turn the dryer off and on. Set requested parameters. No drum light Programme selector in OFF position. Defective light bulb. Turn it to DRUM LIGHT (if available) or to any programme. Replace light bulb (see next section). Abnormally elapsing time on the LCD5) Time to end is calculated on the basis of: type, volume and dampness of laundry. Automatic process; this is not a machine fault. Programme inactive Full water reservoir. Empty water reservoir3) , press START PAUSE button. Drying cycle to Small laundry volume./Too dry laundry for se- Select time programme or higher drying level short lected programme. (e.g. EXTRA DRY ). Fluff filters clogged. Clean fluff filters. Drying cycle to long 6) To high loading volume. Laundry insufficiently spun. Particularly high room temperature - no machine fault. Respect max. loading volume. Spun adequately the laundry. Lower the room temperature if possible. 1) In case of error message on the LCD (e.g. E51- only dryers with the LCD): Switch the dryer off and on. Set programme. Press the START PAUSE button. Does not work? - inform local service and quote the error code. 2) follow program recommendation - see Programme overview chapter 3) see Care and cleaningchapter 4) see Machine settings chapter 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
What to do if ...
Troubleshooting by yourself
Problem
1)
Possible cause
Remedy
Dryer does not
work.
Dryer not connected to mains supply.
Plug in at mains socket. Check fuse in fuse box
(domestic installation).
Loading door opened.
Close loading door
The START PAUSE button not pressed.
Press the START PAUSE button.
Unsatisfactory
drying results.
Incorrect programme set.
Set suitable programme.
2)
Fluff filters clogged.
Clean fluff filters.
3)
Heat exchanger clogged.
Clean heat exchanger.
3)
Max. loading exceeded.
Respect max. loading volume.
Covered ventilation grill.
Uncover ventilation grill in base area.
Residue inside the drum.
Clean the drum inside.
High water hardness.
Set suitable water hardness
4)
.
Loading door
does not close
Filters not locked in place.
Install fine filter and/or snap course filter into
place.
Err
(
Error
) on
the LCD.
5)
Attempt to change parameters after start of the
programme.
Turn the dryer off and on. Set requested param-
eters.
No drum light
Programme selector in OFF position.
Turn it to DRUM LIGHT (if available) or to any
programme.
Defective light bulb.
Replace light bulb (see next section).
Abnormally
elapsing time
on the LCD
5)
Time to end is calculated on the basis of: type,
volume and dampness of laundry.
Automatic process; this is not a machine fault.
Programme in-
active
Full water reservoir.
Empty water reservoir
3)
, press START PAUSE
button.
Drying cycle to
short
Small laundry volume./Too dry laundry for se-
lected programme.
Select time programme or higher drying level
(e.g. EXTRA DRY ).
Drying cycle to
long
6)
Fluff filters clogged.
Clean fluff filters.
To high loading volume.
Respect max. loading volume.
Laundry insufficiently spun.
Spun adequately the laundry.
Particularly high room temperature - no ma-
chine fault.
Lower the room temperature if possible.
1) In case of error message on the LCD (e.g.
E51
- only dryers with the LCD): Switch the dryer off and on. Set programme. Press the
START PAUSE button. Does not work? - inform local service and quote the error code.
2) follow program recommendation - see
Programme overview
chapter
3) see
Care and cleaning
chapter
4) see
Machine settings
chapter
14