ZyXEL G-202 User Guide - Page 74

Additional Setup Requirements, 5.2 The Link Info Screen, Configuration, AP Mode

Get ZyXEL G-202 PDF manuals and user guides View all ZyXEL G-202 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

ZyXEL G-202 User's Guide 5.1.2 Additional Setup Requirements To bridge your wired and wireless network using the G-202, the following requirements must be met: 1 The G-202 must be installed on a computer connected to the wired network. 2 Either bridge the two interfaces (wireless and wired) on the computer (using the Configuration screen of the ZyXEL utility in Windows XP) or configure network sharing (refer to Appendix B on page 87 for an example). 3 Set the wireless station's IP address to be dynamic if you want the wireless stations to access the wired network or the Internet through the G-202. Refer to Appendix E on page 109 for how to configure your computer's IP address. 5.2 The Link Info Screen Select the AP Mode check box and wait for about five seconds to display the screen as shown. Figure 48 Access Point Mode: Link Info The following table describes the labels in this screen. Table 16 Access Point Mode: Link Info LABEL Status SSID DESCRIPTION This field displays the name that identifies your G-202 in the wireless LAN network. 74 Chapter 5 Access Point Mode Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
ZyXEL G-202 User’s Guide
74
Chapter 5 Access Point Mode Configuration
5.1.2
Additional Setup Requirements
To bridge your wired and wireless network using the G-202, the following requirements must
be met:
1
The G-202 must be installed on a computer connected to the wired network.
2
Either bridge the two interfaces (wireless and wired) on the computer (using the
Configuration
screen of the ZyXEL utility in Windows XP) or configure network
sharing (refer to
Appendix B on page 87
for an example).
3
Set the wireless station’s IP address to be dynamic if you want the wireless stations to
access the wired network or the Internet through the G-202. Refer to
Appendix E on page
109
for how to configure your computer’s IP address.
5.2
The Link Info Screen
Select the
AP Mode
check box and wait for about five seconds to display the screen as shown.
Figure 48
Access Point Mode: Link Info
The following table describes the labels in this screen.
Table 16
Access Point Mode: Link Info
LABEL
DESCRIPTION
Status
SSID
This field displays the name that identifies your G-202 in the wireless LAN network.