2010 BMW X3 Owner's Manual - Page 72

2010 BMW X3 Manual

Get 2010 BMW X3 PDF manuals and user guides View all 2010 BMW X3 manuals

Page 72 highlights

Practical interior accessories If the system cannot be operated after repeated programming, check whether the original hand-held transmitter uses an alternating-code system. To do so, either read the instructions of the original hand-held transmitter or press and hold down the programmed memory button 1 of the integrated universal remote control. If the LED 2 on the integrated universal remote control flashes rapidly for a short time then lights up for approx. 2 seconds, this indicates that the original hand-held transmitter uses an alternating-code system. In the case of an alternating-code system, program the memory buttons 1 as described in the section below on alternating-code hand-held transmitters.< If you have questions, please contact your BMW Sports Activity Vehicle Center.< Deleting stored programs Press the left and right memory button 1 for approx. 20 seconds until the LED 2 flashes rapidly: All stored programs are deleted. Reassigning individual programs 1. Hold the original hand-held transmitter at a distance of approx. 4 in/10 cm to 12 in/ 30 cm from the memory buttons 1. The required distance between the hand-held transmitter and memory buttons 1 depends on the relevant system of the original hand-held transmitter used.< 2. Press the desired memory button 1 of the integrated universal remote control. 3. When the LED 2 flashes slowly after approx. 20 seconds, press the transmit button of the original hand-held transmitter. Release both buttons as soon as the LED 2 flashes rapidly. If the LED 2 does not flash rapidly after approx. 15 seconds, then change the distance and repeat the step. Alternating-code hand-held transmitters Consult the operating instructions of the unit you wish to set when programming the integrated universal remote control. You will find information there on the possibilities for synchronization. When programming hand-held transmitters that employ an alternating code, please follow these additional instructions: Programming will be easier with the aid of a second person.< 1. Park your vehicle within the range of the remote-controlled equipment. 2. Program the integrated universal remote control as described above in the section on Fixed-code hand-held transmitters. 3. Locate the button on the receiver of the equipment to be set, e.g. on its drive unit. 4. Press the button on the receiver of the device you want to set up. After step 4, you have approx. 30 seconds for step 5. 5. Press the programmed memory button 1 of the integrated universal remote control three times. The corresponding memory button 1 is now programmed with the signal of the original hand-held transmitter. Digital compass* 1 2 Adjusting button Display The display indicates the cardinal or intercardinal direction in which you are currently driving. 70 Online Edition for Part no. 01 41 2 602 348 - © 02/09 BMW AG

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Practical interior accessories
70
If the system cannot be operated after
repeated programming, check whether
the original hand-held transmitter uses an alter-
nating-code system. To do so, either read the
instructions of the original hand-held transmit-
ter or press and hold down the programmed
memory button
1
of the integrated universal
remote control. If the LED
2
on the integrated
universal remote control flashes rapidly for a
short time then lights up for approx. 2 seconds,
this indicates that the original hand-held trans-
mitter uses an alternating-code system. In the
case of an alternating-code system, program
the memory buttons
1
as described in the sec-
tion below on alternating-code hand-held
transmitters.
<
Alternating-code hand-held
transmitters
Consult the operating instructions of the unit
you wish to set when programming the inte-
grated universal remote control. You will find
information there on the possibilities for syn-
chronization.
When programming hand-held transmitters
that employ an alternating code, please follow
these additional instructions:
Programming will be easier with the aid of
a second person.
<
1.
Park your vehicle within the range of the
remote-controlled equipment.
2.
Program the integrated universal remote
control as described above in the section on
Fixed-code hand-held transmitters.
3.
Locate the button on the receiver of the
equipment to be set, e.g. on its drive unit.
4.
Press the button on the receiver of the
device you want to set up. After step 4, you
have approx. 30 seconds for step 5.
5.
Press the programmed memory button
1
of the integrated universal remote control
three times.
The corresponding memory button
1
is now
programmed with the signal of the original
hand-held transmitter.
If you have questions, please contact your
BMW Sports Activity Vehicle Center.
<
Deleting stored programs
Press the left and right memory button
1
for
approx. 20 seconds until the LED
2
flashes rap-
idly:
All stored programs are deleted.
Reassigning individual programs
1.
Hold the original hand-held transmitter at a
distance of approx. 4 in/10 cm to 12 in/
30 cm from the memory buttons
1
.
The required distance between the
hand-held transmitter and memory
buttons
1
depends on the relevant system
of the original hand-held transmitter used.
<
2.
Press the desired memory button
1
of the
integrated universal remote control.
3.
When the LED
2
flashes slowly after approx.
20 seconds, press the transmit button of
the original hand-held transmitter. Release
both buttons as soon as the LED
2
flashes
rapidly. If the LED
2
does not flash rapidly
after approx. 15 seconds, then change the
distance and repeat the step.
Digital compass*
1
Adjusting button
2
Display
The display indicates the cardinal or intercardi-
nal direction in which you are currently driving.
Online Edition for Part no. 01 41 2 602 348 - © 02/09 BMW AG