2015 Chrysler Town & Country User Guide - Page 92

2015 Chrysler Town & Country Manual

Get 2015 Chrysler Town & Country PDF manuals and user guides View all 2015 Chrysler Town & Country manuals

Page 92 highlights

ELECTRONICS NOTE: Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at HomeLink.com for information or assistance. Programming A Rolling Code NOTE: For programming Garage Door Openers that were manufactured after 1995. These Garage Door Openers can be identified by the "LEARN" or "TRAIN" button located where the hanging antenna is attached to the Garage Door Opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. 1. Place the ignition switch into the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. 3. Push and hold the HomeLink® button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold both buttons and observe the indicator light. The HomeLink® indicator will flash slowly and then rapidly after HomeLink® has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. 5. At the garage door opener motor (in the garage), locate the "LEARN" or "TRAINING" button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor. Firmly push and release the "LEARN" or "TRAINING" button. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pushed. 6. Return to the vehicle and push the programmed HomeLink® button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. NOTE: If the device does not activate, push the button a third time (for two seconds) to complete the training. 7. To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
NOTE:
ErasingallchannelsshouldonlybeperformedwhenprogrammingHomeLink®forthefirsttime.
Donoterasechannelswhenprogrammingadditionalbuttons.
Ifyouhaveanyproblems,orrequireassistance,pleasecalltoll-free1-800-355-3515or,onthe
InternetatHomeLink.comforinformationorassistance.
ProgrammingARollingCode
NOTE:
For programming Garage Door Openers that were manufactured after 1995. These Garage
DoorOpenerscanbeidentifiedbythe“LEARN”or“TRAIN”buttonlocatedwherethehanging
antennaisattachedtotheGarageDoorOpener.ItisNOTthebuttonthatisnormallyusedto
openandclosethedoor.Thenameandcolorofthebuttonmayvarybymanufacturer.
1. PlacetheignitionswitchintotheON/RUNposition.
2. Placethehand-heldtransmitter1to3inches(3to8cm)awayfromtheHomeLink®buttonyou
wishtoprogramwhilekeepingtheHomeLink®indicatorlightinview.
3. Push and hold the HomeLink® button you want to program while you push and hold the
hand-heldtransmitterbutton.
4. Continuetoholdbothbuttonsandobservetheindicatorlight.TheHomeLink®indicatorwill
flash slowly and then rapidly after HomeLink® has received the frequency signal from the
hand-heldtransmitter.Releasebothbuttonsaftertheindicatorlightchangesfromslowto
rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING”
button.Thiscanusuallybefoundwherethehangingantennawireisattachedtothegarage
dooropenermotor.Firmlypushandreleasethe“LEARN”or“TRAINING”button.
NOTE:
Youhave30secondsinwhichtoinitiatethenextstepaftertheLEARNbuttonhasbeenpushed.
6. ReturntothevehicleandpushtheprogrammedHomeLink®buttontwice(holdingthebutton
for two seconds each time). If the device is plugged in and activates, programming is
complete.
NOTE:
Ifthedevicedoesnotactivate,pushthebuttonathirdtime(fortwoseconds)tocompletethe
training.
7. To program the remaining two HomeLink® buttons, repeat each step for each remaining
button.DONOTerasethechannels.
ELECTRONICS
90