2015 Dodge Challenger User Guide - Page 172

2015 Dodge Challenger Manual

Page 172 highlights

W H AT T O D O I N E M E R G E N C I E S 4. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem. 5. Uncoil the Power Plug (8) and insert the plug into the vehicle's 12 Volt power outlet. 6. Do not remove foreign objects (e.g., screws or nails) from the tire. (C) Injecting Tire Service Kit Sealant Into The Deflated Tire: Always start the engine before turning ON the Tire Service Kit. NOTE: Manual transmission vehicles must have the parking brake engaged and the shift lever in NEUTRAL. After pressing the Power Button (4), the sealant (white fluid) will flow from the Sealant Bottle (1) through the Sealant Hose (6) and into the tire. NOTE: Sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 - 10 seconds through the Sealant Hose (6): 1. Press the Power Button (4) to turn Off the Tire Service Kit. Disconnect the Sealant Hose (6) from the valve stem. Make sure the valve stem is free of debris. Reconnect the Sealant Hose (6) to the valve stem. Check that the Mode Select Knob (5) is in the Sealant Mode position and not Air Mode. Press the Power Button (4) to turn On the Tire Service Kit. 2. Connect the Power Plug (8) to a different 12 Volt power outlet in your vehicle or another vehicle, if available. Make sure the engine is running before turning ON the Tire Service Kit. 3. The Sealant Bottle (1) may be empty due to previous use. Call for assistance. NOTE: If the Mode Select Knob (5) is on Air Mode and the pump is operating, air will dispense from the Air Pump Hose (7) only, not the Sealant Hose (6). If the sealant (white fluid) does flow through the Sealant Hose (6): 1. Continue to operate the pump until sealant is no longer flowing through the hose (typically takes 30 - 70 seconds). As the sealant flows through the Sealant Hose (6), the Pressure Gauge (3) can read as high as 70 psi (4.8 Bar). The Pressure Gauge (3) will decrease quickly from approximately 70 psi (4.8 Bar) to the actual tire pressure when the Sealant Bottle (1) is empty. 2. The pump will start to inject air into the tire immediately after the Sealant Bottle (1) is empty. Continue to operate the pump and inflate the tire to the pressure indicated on the tire pressure label on the driver-side latch pillar (recommended pressure). Check the tire pressure by looking at the Pressure Gauge (3). 170

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236

4. Remove the cap from the valve stem and then screw the fitting at the end of the
SealantHose(6)ontothevalvestem.
5. UncoilthePowerPlug(8)andinserttheplugintothevehicle’s12Voltpoweroutlet.
6. Donotremoveforeignobjects(e.g.,screwsornails)fromthetire.
(C)InjectingTireServiceKitSealantIntoTheDeflatedTire:
AlwaysstarttheenginebeforeturningONtheTireServiceKit.
NOTE:
Manualtransmissionvehiclesmusthavetheparkingbrakeengagedandtheshiftleverin
NEUTRAL.
AfterpressingthePowerButton(4),thesealant(whitefluid)willflowfromtheSealant
Bottle(1)throughtheSealantHose(6)andintothetire.
NOTE:
Sealantmayleakoutthroughthepunctureinthetire.
If the sealant (white fluid) does not flow within 0 – 10 seconds through the Sealant
Hose(6):
1. Press the Power Button (4) to turn Off the Tire Service Kit. Disconnect the Sealant
Hose(6)fromthevalvestem.Makesurethevalvestemisfreeofdebris.Reconnectthe
Sealant Hose (6) to the valve stem. Check that the Mode Select Knob (5) is in the
SealantModepositionandnotAirMode.PressthePowerButton(4)toturnOntheTire
ServiceKit.
2. Connect the Power Plug (8) to a different 12 Volt power outlet in your vehicle or
anothervehicle,ifavailable.MakesuretheengineisrunningbeforeturningONthe
TireServiceKit.
3. TheSealantBottle(1)maybeemptyduetoprevioususe.Callforassistance.
NOTE:
IftheModeSelectKnob(5)isonAirModeandthepumpisoperating,airwilldispense
fromtheAirPumpHose(7)only,nottheSealantHose(6).
Ifthesealant(whitefluid)doesflowthroughtheSealantHose(6):
1. Continue to operate the pump until sealant is no longer flowing through the hose
(typicallytakes30-70seconds).AsthesealantflowsthroughtheSealantHose(6),
thePressureGauge(3)canreadashighas70psi(4.8Bar).ThePressureGauge(3)
willdecreasequicklyfromapproximately70psi(4.8Bar)totheactualtirepressure
whentheSealantBottle(1)isempty.
2. ThepumpwillstarttoinjectairintothetireimmediatelyaftertheSealantBottle(1)
isempty.Continuetooperatethepumpandinflatethetiretothepressureindicated
on the tire pressure label on the driver-side latch pillar (recommended pressure).
CheckthetirepressurebylookingatthePressureGauge(3).
WHAT TO DO IN EMERGENCIES
170