AIWA NSX-MTD9 Operating Instructions - Page 30

Presetting Stations

Get AIWA NSX-MTD9 PDF manuals and user guides View all AIWA NSX-MTD9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Keep DOWN or UP pressed until the frequency starts to change rapidly. After tuning in to a station, the search stops. To stop the Auto Search manually, press DOWN or UP. • The Auto Search may not stop at stations with very weak signals. When an FM stereo broadcast contains noise Press MONO TUNER on the remote control so that "MONO" appears on the display. Noise is reduced, although reception is monaural. To restore stereo reception, press the button again so that MONO disappears. To change the AM tuning interval The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the tuning interval. Press POWER while pressing . To reset the interval, repeat this procedure. When the AM tuning interval is changed, all preset stations are cleared. The preset stations have to be set again. PRESETTING STATIONS The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Press the TUNER/BAND to select a band, and press DOWN or UP to select a station. 2 Press SET to store the station. A station is assigned a preset number, beginning from 1 in consecutive order for each band. 3 Repeat steps 1 and 2. The next station will not be stored if a total of 32 preset stations for all the bands have already been stored. "FULL" is displayed if you attempt to store more than 32 preset stations.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Keep
DOWN or
UP pressed until the frequency starts to change rapidly. After tuning in to a station,
the search stops. To stop the Auto Search manually, press
DOWN or
UP
.
• The Auto Search may not stop at stations with very weak signals.
When an FM stereo broadcast contains noise
Press
MONO TUNER
on the remote control so that "MONO" appears on the disp
lay.
Noise is reduced, although reception is monaural.
To restore stereo reception, press the button again so that MONO disappears.
To change the AM tuning interval
The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an ar
ea where the frequency
allocation system is 9 kHz/step, change the tuning interval.
Press
POWER
while pressing
. To reset the interval, repeat this procedure.
When the AM tuning interval is changed, all preset stations are cleared. The preset stations h
ave to be set again.
PRESETTING STATIONS
The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station.
Use the preset number to tune in to a preset station directly.
1 Press the TUNER/BAND to select a band, and press
DOWN or
UP to se
lect a station.
2 Press
SET to store the station.
A station is assigned a preset number, beginning from 1 in consecutive order for each band.
3 Repeat steps 1 and 2.
The next station will not be stored if a total of 32 preset stations for all the bands
have already been stored.
"FULL" is displayed if you attempt to store more than 32 preset stations.