AIWA NSX-MTD9 Operating Instructions - Page 51

Setting The Sleep Timer

Get AIWA NSX-MTD9 PDF manuals and user guides View all AIWA NSX-MTD9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

The clock is displayed. (The ":" between the hours and minutes flashes.) When the power cord is plugged into an AC outlet for the first time after purchase or when the clock setting is canceled due to a power failure, the entire clock display flashes. 1 Press CLOCK. 2 Within 4 seconds, turn MULTI JOG to designate the hour and the minute. Turning MULTI JOG changes both the hour and the minute. or is also available instead of MULTI JOG. Holding these buttons down will vary the time rapidly. 3 Press ENTER or . The clock starts from 00 second. To restore an original clock setting Press CLOCK before completing step 3 to restore the previous time setting. This cancels any new setting. To view the clock when another display is in the display Press CLOCK. The time is displayed for 4 seconds and then the original display reappears. However, the clock cannot be displayed during recording. To switch to the 24-hour standard Press CLOCK and then press within 4 seconds. Repeat the same procedure to restore the 12-hour standard. If the clock display flashes This caused by a power interruption. The current time needs to be reset. If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be reset. If the power-economizing mode (page 6) is on, all the display lights turn off when the power is turned off. To view the clock, press CLOCK so that the time is displayed for 4 seconds. SETTING THE SLEEP TIMER

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
The clock is displayed. (The ":" between the hours and minutes flashes.) When the power cord is plugged into an AC
outlet for the first time after purchase or when the clock setting is canceled due to a power failure, the entire clock
display flashes.
1
Press CLOCK.
2
Within 4 seconds,
turn MULTI JOG to designate the hour and the minute.
Turning
MULTI JOG
changes both the hour and the minute.
or
is also available instead of
MULTI
JOG.
Holding these buttons down will vary the time rapidly.
3 Press ENT
ER or
.
The clock starts from 00 second.
To restore an original clock setting
Press
CLOCK
before completing step 3 to restore the previous time setting. This cancels any new setting.
To view the clock when another display is in the display
Press
CLOCK.
Th
e time is displayed for 4 seconds and then the original display reappears. However, the clock
cannot be displayed during recording.
To switch to the 24-hour standard
Press
CLOCK
and then press
within 4 seconds. Repeat the same procedure to restore the 12
-hour standard.
If the clock display flashes
This caused by a power interruption. The current time needs to be reset.
If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be
reset.
If the powe
r-economizing mode (page 6) is on, all the display lights turn off when the power is turned off. To view
the clock, press
CLOCK
so that the time is displayed for 4 seconds.
SETTING THE SLEEP TIMER