Alpine IVA D105 Owners Manual - Page 52

Adjusting the DVD Level The volume (signal level) for Dolby Digital, Dolby PL II, DTS and PCM modes can be set. Setting item : DVD LEVEL • Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. The setting is canceled if the Decode mode is switched. Adjust the level by touching [ ] or [ ] of the desired adjusting mode. The level can be adjusted in the range of -5 to +5. Storing Settings in the Memory Adjustment or setting contents can be stored. Contents that can be stored vary depends on the audio processor used. Setting item : USER PRESET 1 Touch [ ] or [ ] of USER PRESET to select any one of the preset buttons (P-1 through P-6). 2 Touch [MEMORY]. The setting contents are stored. • The stored contents will not be deleted even when the battery power cord is detached. Recalling the Preset Memory Touch [ ] or [ ] of A.PROCESSOR to select the preset memory you want to recall from P-1 through P-6. • It takes a few moment to recall the preset memory. Using the Pro Logic II Mode Pro Logic processing can be conducted on the music signals recorded on two channels to achieve Dolby Pro Logic II surround sound. For two-channel Dolby Digital and DTS signals, there is also a "REAR FILL" function for outputting the signals of the front channel to the rear channel. Setting item : DOLBY PLII/REAR FILL Touch [ ] or [ ] of DOLBY PLII/REAR FILL to select the desired mode. PL II MOVIE: Suits the stereo TV shows and all programs encoded in Dolby Surround. It improves the sound field directivity to near that of discrete 5.1-channel sound. PL II MUSIC: Can be used for all stereo music recordings, and provides a wide, deep sound field. OFF: Turns DOLBY PL II function to OFF. PANORAMA: Widens the soundstage of the front stereo Image (BassEngine to extend to the surround speakers. only) If PL II MUSIC is selected, the center width can be adjusted with following operations. This function offers the optimum vocal position by adjusting the center channel position between the center speaker and the L/R speaker. (The adjustments established in "Adjusting the acoustic image (BI-PHANTOM)" (page 49) are ineffective while this function is activated.) Touch [ ] or [ ] of CENTER WIDTH CONT. to adjust the level. The level can be adjusted between 0 to 7. When the level increases, the center channel position moves from the center speaker position to both sides. Touch [OFF] of CENTER WIDTH CONT. to turn off the center width control. • The setting can be made only when an external audio processor is connected. When the Bass Engine mode is set, the level setting is fixed to "3." • This adjustment is effective when the setting of the center speaker is SMALL or LARGE in the speaker setup settings. • "REAR FILL" function Depending on the input signals, the sound may only be output from the front speakers. In this case, the "REAR FILL" function can be used to output signals from the rear speakers as well. • If REAR FILL is set, 192kHz, 96kHz, etc., contents are down sampled to 48kHz. • Avoid stopping, pausing, switching the disc, cueing, fast-forwarding or switching the audio channel of this unit while making this adjustment. The setting is canceled if the Decode mode is switched. • This adjustment is ineffective when the speaker is set to CENTER OFF in "Setting the Speakers" (page 44). • This function only works with two-channel signals. This operation is ineffective when 5.1-channel DTS or Dolby Digital signals are input. • If the setting of REAR FILL is made when REAR MIX is ON, sound is unchanged in the rear fill setting because REAR MIX is given priority during 2 channel decoder other than linear PCM. • For linear PCM signals, the voice is output from the rear speaker regardless of the REAR FILL and REAR MIX setting. • Touching [RETURN] will return to the previous screen. Linear PCM Setting The output when playing discs recorded in linear PCM can be set to 2 or 3 channels. Setting item : PCM MODE Touch [ ] or [ ] of PCM MODE to select 2 CH or 3 CH. 2CH: 2ch output (L/R) 3CH: 3ch output (L/R/CENTER) • This adjustment is ineffective when the speaker is set to CENTER OFF in "Setting the Speakers" (page 44). 50-EN