Alpine KTP-445U Owners Manual - Page 4

Specifications, Accessories, Installation Fig. 1, Fig. 2

Get Alpine KTP-445U PDF manuals and user guides View all Alpine KTP-445U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

SPECIFICATIONS Input Sensitivity Crossover Dimensions NOTE: • For product improvement, specifications and design are subject to change without notice. ACCESSORIES • Mounting Bracket ...2 • Self-Tapping Screw (M4 x 12) ...4 • Cable Tie ...2 • Input Wire Harness ...1 • Output/Power Wire Harness ...1 INSTALLATION (Fig. 1 and Fig. 2) With this amplifier, there are two options for installation. Depending on which is best for your tarQet location, refer to .instructions A or B below. ~CAUTION + Caution on connection terminals/parts • Keep electrically conductive objects away from the unit's terminals/parts (power terminals, fuses, speaker output terminals, RCA connectors, etc.). Doing so prevents a possible short circuit and damage to the unit. A. Installation with mounting brackets 1. Remove the two bottom screws on each end panel. 2. Use these screws to attach the included mounting brackets. 3. Using the amplifier as a template, mark the four screw locations. 4. Make sure there are no objects behind the surface that may become damaged during drilling. 5. Drill the screw holes. 6. Position the KTP-445U over the screw holes, and secure with four self-tapping screws. 7. Position the unit over the screw holes you prepared earlier. 8. Fasten the unit down with the four self-tapping screws (M4 x 12). Refer to Fig. 1. B. Installation with chassis mounting loops 1. Push each of the included cable ties through the two mounting loops near each end on the bottom panel. 2. Use the cable ties to securely attach the amplifier to the vehicle's frame or chassis. Refer to Fig. 2. NOTE: • To securely connect the ground lead, use an already installed screw on the metal part ofthe vehicle (marked*). Be sure this is a good ground by checking continuity to the battery (-) terminal. As much as possible connect all equipment to the same ground point. These procedures will help eliminate noise.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
SPECIFICATIONS
Input Sensitivity
Crossover
Dimensions
NOTE:
•
For product improvement, specifications and design are subject to change without notice.
ACCESSORIES
• Mounting Bracket
...........................................................................................................................................................................
2
• Self-Tapping Screw (M4 x 12)
........................................................................................................................................................
4
• Cable Tie
........................................................................................................................................................................................
2
• Input Wire Harness
........................................................................................................................................................................
1
• Output/Power Wire Harness
..........................................................................................................................................................
1
INSTALLATION (Fig. 1
and
Fig. 2)
With this amplifier, there are two options for installation. Depending on which is best for your
tarQet
location, refer
to .instructions A or B below.
~CAUTION
+
Caution on connection terminals/parts
• Keep electrically conductive objects away from the unit's terminals/parts (power terminals, fuses, speaker
output terminals, RCA connectors, etc.). Doing so prevents a possible short circuit and damage
to
the unit.
A. Installation with mounting brackets
1.
Remove the two bottom screws on each end panel.
2.
Use these screws to attach the included mounting brackets.
3.
Using the amplifier as a template, mark the four screw locations.
4.
Make sure there are no objects behind the surface that may become damaged during drilling.
5.
Drill the screw holes.
6.
Position the KTP-445U over the screw holes, and secure with four self-tapping screws.
7.
Position the unit over the screw holes you prepared earlier.
8.
Fasten the unit down with the four self-tapping screws (M4 x 12). Refer to Fig.
1.
B.
Installation with chassis mounting loops
1.
Push each of the included cable ties through the two mounting loops near each end on the bottom panel.
2.
Use the cable ties to securely attach the amplifier
to
the vehicle's frame or chassis. Refer to
Fig.
2.
NOTE:
•
To
securely connect the ground lead, use an already installed screw on the metal
part
of
the vehicle
(marked*).
Be
sure this is a
good
ground by checking continuity to the battery (-) terminal.
As
much as possible
connect all equipment to the same ground point. These procedures will help eliminate noise.