Alpine i407-WRA-JL Owners Manual English - Page 64

Accessory List, Installation, Caution concerning the installation location, Mounting the Microphone

Get Alpine i407-WRA-JL PDF manuals and user guides View all Alpine i407-WRA-JL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Accessory List Main unit 1 Quick Reference Guide 1set Power cable 1 USB extension cable 1 PRE OUT cable 1 Microphone 1 CAN Interface Connector 1 Screw (M5×8 4 When you speak into the microphone, you should not have to change your driving posture. This may cause a distraction, taking your attention away from safely driving your vehicle. Carefully consider direction and distance while mounting the microphone. Confirm that the driver's voice can be easily picked up at the selected location. Cable clamp (sold separately) Microphone Installation Caution • Do not block the unit's fan, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Heat sink Installation example using the Original Mounting Bracket 1 Mount the original mounting bracket to the unit using the supplied screws. Rear of the Unit Caution concerning the installation location Angle of installation Install at an angle between horizontal and 30°. Note that installing at an angle outside of this range will result in a loss of performance and possibly damage. 0 - 30° Mounting the Microphone For safe use, make sure of the following: • Location is stable and firm. • Does not interfere with safety equipment. • Driver's view and operations are not obstructed. • Microphone is located where the driver's voice can be easily picked up (for example, on the sun visor). 64-EN Original Mounting Bracket Screws (M5×8) (included) Ground Lead* Chassis 2 Connect all other leads of the unit according to details described in the "Connections" (page 65). 3 Mount the unit in a car. * To securely connect the ground lead, use an already installed screw on a metal part of the vehicle (marked ( )) or a clean, bare metal spot on the vehicle's chassis. • Fix the cables carefully. Do not damage them by mounting them into movable parts, such as the seat rail, or by locating them against sharp or pointed edges. 4 Reattach the removed vehicle parts (panels, etc.) or other aftermarket dash kit back onto the vehicle.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
64
-EN
Accessory List
Main unit
.................................................................................................
1
Quick Reference Guide
.................................................................
1set
<Cables>
Power cable
............................................................................................
1
USB extension cable
............................................................................
1
PRE OUT cable
.......................................................................................
1
Microphone
............................................................................................
1
CAN Interface Connector
..................................................................
1
<Main unit mounting parts>
Screw (M5×8)
.........................................................................................
4
Installation
Caution
• Do not block the unit’s fan, thus preventing air
circulation. If blocked, heat will accumulate inside the
unit and may cause a fire.
Heat sink
Rear of the Unit
Caution concerning the installation
location
Angle of installation
Install at an angle between horizontal and 30°. Note that
installing at an angle outside of this range will result in a
loss of performance and possibly damage.
0 - 30°
Mounting the Microphone
For safe use, make sure of the following:
•
Location is stable and firm.
•
Does not interfere with safety equipment.
•
Driver’s view and operations are not obstructed.
•
Microphone is located where the driver’s voice can be
easily picked up (for example, on the sun visor).
When you speak into the microphone, you should not have
to change your driving posture. This may cause a
distraction, taking your attention away from safely driving
your vehicle. Carefully consider direction and distance while
mounting the microphone. Confirm that the driver’s voice
can be easily picked up at the selected location.
Microphone
Cable clamp
(sold separately)
Installation example using the
Original Mounting Bracket
1
Mount the original mounting bracket to the
unit using the supplied screws.
Original Mounting Bracket
Ground Lead*
Chassis
Screws (M5×8)
(included)
2
Connect all other leads of the unit according
to details described in the “Connections”
(page 65).
3
Mount the unit in a car.
*
To securely connect the ground lead, use an already
installed screw on a metal part of the vehicle (marked
(
)) or a clean, bare metal spot on the vehicle’s
chassis.
•
Fix the cables carefully. Do not damage them by
mounting them into movable parts, such as the seat
rail, or by locating them against sharp or pointed
edges.
4
Reattach the removed vehicle parts (panels,
etc.) or other aftermarket dash kit back onto
the vehicle.