Asus Terminator Tualatin 786 MANUAL TERMINATOR TUALATIN English V1.0 - Page 53

Internal Connectors

Get Asus Terminator Tualatin PDF manuals and user guides View all Asus Terminator Tualatin manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

3.9.2 Internal Connectors 1. Primary (Blue)/Secondary IDE Connectors (40-1pin IDE1/IDE2) These connectors support the provided UltraDMA/100/66/33 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/100/66/33 slave device (hard disk drive) and the black connector to the UltraDMA/ 100/66/33 master device. It is recommended that non-UltraDMA/ 100/66/33 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup (see 5.6 Boot Menu). If you have more than two UltraDMA/66/33 devices, purchase another UltraDMA/ 100/66/33 cable. NOTES: 1. Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. This prevents incorrect orientation when you connect the cables. 2. The hole near the blue connector on the UltraDMA/66 cable is intentional. TIP: You may configure two hard disks to be both Masters with two ribbon cables - one for the primary IDE connector and another for the secondary IDE connector. IMPORTANT Use only 40-pin 80-conductor IDE cables for UltraDMA/66 IDE devices. TUSC Secondary IDE Connector Primary IDE Connector ® NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. TUSC IDE Connectors PIN 1 ASUS Terminator Barebone System 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
ASUS Terminator Barebone System
53
1.
Primary (Blue)/Secondary IDE Connectors (40-1pin IDE1/IDE2)
These connectors support the provided UltraDMA/100/66/33 IDE
hard
disk ribbon cable. Connect the cable’s blue connector to
the primary (recommended) or secondary IDE connector, then
connect the gray connector to the UltraDMA/100/66/33 slave
device (hard disk drive) and the black connector to the UltraDMA/
100/66/33 master device. It is recommended that non-UltraDMA/
100/66/33 devices be connected to the secondary IDE connector.
If you install two hard disks, you must configure the second drive
as a slave device by setting its jumper accordingly. Refer to the
hard disk documentation for the jumper settings. BIOS supports
specific device bootup (see
5.6 Boot Menu
).
If you have more
than two UltraDMA/66/33 devices, purchase another UltraDMA/
100/66/33 cable.
NOTES:
1. Pin 20 on each IDE connector is removed to match the
covered hole on the UltraDMA cable connector. This prevents
incorrect orientation when you connect the cables.
2.
The hole near the blue connector on the UltraDMA/66 cable
is intentional.
TIP:
You may configure two hard disks to be both Masters with two
ribbon cables – one for the primary IDE connector and another for
the secondary IDE connector.
3.9.2
Internal Connectors
IMPORTANT
Use only 40-pin 80-conductor IDE cables for UltraDMA/66 IDE
devices.
TUSC
®
TUSC IDE Connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
Primary IDE Connector
Secondary IDE Connector
PIN 1