Home » Beltronics Manuals » Radar Detectors & Jammers » Beltronics Vector 995 » Manual Viewer

Beltronics Vector 995 Owner's Manual

Beltronics Vector 995 Manual

View all Beltronics Vector 995 manuals

Add to My Manuals
Save this manual to your list of manuals

Beltronics Vector 995 manual content summary:

Beltronics Vector 995 | Owner's Manual - Page 1
31160_Vec995_OMrev 8/10/10 1:46 PM Page 1 Beltronics 5442 West Chester Road West Chester OH 45069 USA USA 800-341-2288 www.beltronics.com ©2010 Beltronics Designed and Manufactured In Canada Features, specifications and prices subject to change without notice. Model: V995 121V995-1 Owner's Manual
Beltronics Vector 995 | Owner's Manual - Page 2
ve used a radar detector before, a review of the Quick Reference Guide on pages 4 and 5, and the Programming information on pages 12 and 13 will brieﬂy explain the new features. If this is your ﬁrst detector, please read the manual in detail to get the most out of your V995's outstanding performance
Beltronics Vector 995 | Owner's Manual - Page 3
Details of Programming Technical Details • Speciﬁcations • Interpreting Alerts • How Radar Works • How "POP" Works • How Laser Works • TSR Signal Ranking Software • How Safety Radar Works Service • Troubleshooting • Service • Registration • Warranty and Accessories 12-16 12 12 13 14-16 17-23 17 18
Beltronics Vector 995 | Owner's Manual - Page 4
1:46 PM Page 7 Quick Reference Guide To begin using your V995, just follow these simple steps 1 Plug the small end of the power cord into the side jack of the detector, and plug the large end of the power cord into your car's lighter socket. 2 Mount your V995 on the windshield using the supplied
Beltronics Vector 995 | Owner's Manual - Page 5
ignition switch. Optional power cords See the Accessories section for details on our optional coiled SmartPlug or Direct-wire power cords. Page 29 Mounting Location WARNING: BELTRONICS cannot anticipate the many ways the V995 can be mounted. It is important that you mount V995 where it will not
Beltronics Vector 995 | Owner's Manual - Page 6
. If you prefer, you can select alternate power-on displays. See the Programming section for details. Voice Alerts The V995 provides digital voice announcements of radar and laser bands detected. If Safety Radar (SWS) is turned on, a safety radar message will also be announced. See the Programming
Beltronics Vector 995 | Owner's Manual - Page 7
text message. A complete listing of the text messages is on page 23. Power Connector V995's power jack uses a telephone-type connector. This 4-conductor connector only works with the included power cord, optional direct-wire, or SmartPlug cord. For more information or to order, call us toll-free at
Beltronics Vector 995 | Owner's Manual - Page 8
operation. 12 Overview of Programming Press the REVIEW button to go from one category to the next PILOT (Power-on indication) VOICE POWER-ON SEQUENCE SIGNAL STRENGTH METER AUTOMUTE CITY MODE SENSITIVITY BANDS * Factory Default Settings To reset V995 to its original factory settings, press and
Beltronics Vector 995 | Owner's Manual - Page 9
this setting, only the distinct audio tone will be heard when a radar, Laser, or SWS message is detected. Power-on Sequence PwrOnSTD (Standard) In this setting, each time you turn on V995, it will display "BEL V995," "Laser," "Kaband," "K-band," "X-band," followed by a brief X-band alert. (factory
Beltronics Vector 995 | Owner's Manual - Page 10
of Brightness, plus Dark Mode Power Requirement • 12VDC, Negative Ground • Power cord (included) Programmable Features • Power-On Indication • Voice Alerts • Power-On Sequence • Signal Strength Meter • AutoMute • City Mode Sensitivity • Radar / Laser Bands Sensitivity Control • Highway, AutoScan
Beltronics Vector 995 | Owner's Manual - Page 11
. The following examples will give you an introduction to understanding the V995's warning system for radar, laser and safety alerts. Alert The V995 begins to sound slowly, then the rate of alert increases. The Signal Meter ramps accordingly. V995 emits short alerts for a few seconds and then falls
Beltronics Vector 995 | Owner's Manual - Page 12
cars, trucks, even guardrails and overpasses. Radar works by directing its microwave beam down the road. As your vehicle travels into range, the microwave beam bounces off your car, and the radar antenna tracking history, (required by law). 20 How Laser (Lidar) Works Laser speed detection is
Beltronics Vector 995 | Owner's Manual - Page 13
TSR Signal Ranking Software Your radar detector includes a new optional boost in anti-falsing software to eliminate Radar Works Safety Warning System, or SWS, uses a modiﬁed K-band radar signal. The SWS safety radar system has 64 possible messages (60 currently allocated). The SWS messages your V995
Beltronics Vector 995 | Owner's Manual - Page 14
messages (pages 22-23) Caution V995 has detected a Safety Radar Signal, but the signal isn't yet strong enough to decode the speciﬁc safety message (page 22-23) Self Cal V995 is running a self-calibration test Service V995 has failed the calibration test. Contact Beltronics for repair Required 25
Beltronics Vector 995 | Owner's Manual - Page 15
our web address: www.beltronics.com. 1. First Name Middle Initial____ Last Name Address City State ZIP Phone Number (In case we have a question 2. Product Purchased Vector 995 Radar & Laser Detector Serial Number 3. Place of Purchase Date_________ Price 4. Primary reason for purchasing
Beltronics Vector 995 | Owner's Manual - Page 16
The following accessories and replacement parts are available for BEL V995. Standard Coiled Power Cord.........$14.00 Direct-wire Power Cord 10.00 Coiled SmartPlug 29.95 Direct-wire SmartPlug 29.95 Accessory Kit 19.95 Extra Windshield Mount 4.00 Features, speciﬁcations and prices are subject