BenQ MP612C User Manual - Page 40

Personalizing the projector menu display, Shutting down the projector

Get BenQ MP612C - SVGA DLP Projector PDF manuals and user guides
UPC - 840046018771
View all BenQ MP612C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. • Menu Display Time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last button press. The time length ranges from 5 to 30 seconds in 5-second increments. Use Left/ Right to select a suitable time. • Menu Position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use Left/ Right to select a preferred position. • Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OnScreen (OSD) Menus. Use Left/ Right to select your language. • Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use Left/ Right to select a screen. Shutting down the projector 1. Press II Power and a POWER OFF confirmation message will display prompting you. If you don't respond in a few Press button again to power off seconds, the message will Press any button to cancel disappear. 2. Press II Power a second time. The Power indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. To protect the lamp, the projector will not respond to any commands during the cooling process. 3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. The Power indicator light is a steady orange and fans stop. Disconnect the power cord from the wall socket. • Do not unplug the power cord before the projector shutdown sequence is complete or during the 90second cooling down process. • If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press Power again to start the projector after the fans stop and the Power indicator light turns orange. 40 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Operation
40
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu Display Time
in the S
YSTEM SETUP: Advanced
>
Menu Settings
menu sets the
length of time the OSD will remain active after your last button press. The time length
ranges from 5 to 30 seconds in 5-second increments. Use
Left
/
Right
to select a
suitable time.
•
Menu Position
in the S
YSTEM SETUP: Advanced
>
Menu Settings
menu sets the OSD
position in five locations. Use
Left
/
Right
to select a preferred position.
•
Language
in the S
YSTEM SETUP: Basic
menu sets your familiar language for the On-
Screen (OSD) Menus. Use
Left
/
Right
to select your language.
•
Splash Screen
in the
SYSTEM SETUP: Basic
menu sets a preferred logo screen to be
displayed during projector start-up. Use
Left
/
Right
to select a screen.
Shutting down the projector
1.
Press
Power
and a
confirmation message will display
prompting you.
If you don't respond in a few
seconds, the message will
disappear.
2.
Press
Power
a second time.
The
Power indicator light
flashes
orange, the projection lamp shuts
down, and the fans will continue
to run for approximately 90
seconds to cool down the projector.
To protect the lamp, the projector will not respond to any commands during the cooling
process.
3.
Once the cooling process finishes, a "
Power Off
Ring Tone
" will be heard. The Power indicator
light is a steady orange and fans stop.
Disconnect the power cord from the wall
socket.
•
Do not unplug the power cord before the projector
shutdown sequence is complete or during the 90-
second cooling down process.
•
If the projector is not properly shut down, to protect the lamp, when you attempt to re-start
the projector, the fans will run for a few minutes to cool down. Press Power again to start
the projector after the fans stop and the Power indicator light turns orange.
POWER OFF
Press
button
again to power off
Press any button to cancel
I
I
I
I