BenQ MP612C User Manual - Page 54

As shown in the lower the new lamp, first into the connector on the projector

Get BenQ MP612C - SVGA DLP Projector PDF manuals and user guides
UPC - 840046018771
View all BenQ MP612C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

3. Remove the lamp cover from the projector. • Do not turn the power on with the lamp cover removed. • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries. 4. Loosen the screw that secures the lamp. 5. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials. • Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images. 6. As shown in the figure, lower the new lamp first into the connector on the projector and align the two holes on the projector. 7. Tighten the screw that secures the lamp. • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 8. Ensure the handle is fully laid flat and locked in place. 54 Maintenance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Maintenance
54
3.
Remove the lamp cover from the projector.
•
Do not turn the power on with the lamp cover
removed.
•
Do not insert your fingers between the lamp and
the projector. The sharp edges inside the
projector may cause injuries.
4.
Loosen the screw that secures the lamp.
5.
Lift the handle so that it stands up. Use the
handle to slowly pull the lamp out of the
projector.
•
Pulling it too quickly may cause the lamp to break
and scatter broken glass in the projector.
•
Do not place the lamp in locations where water
might splash on it, children can reach it, or near
flammable materials.
•
Do not insert your hands into the projector after
the lamp is removed. If you touch the optical
components inside, it could cause color
unevenness and distortion of the projected
images.
6.
As shown in the figure, lower the new lamp
first into the connector on the projector and
align the two holes on the projector.
7.
Tighten the screw that secures the lamp.
•
Loose screw may cause a bad connection, which
could result in malfunction.
•
Do not over tighten the screw.
8.
Ensure the handle is fully laid flat and locked in
place.