Biostar M6VCT M6VCT user's manual - Page 71

Set Supervisor/User Password

Get Biostar M6VCT PDF manuals and user guides View all Biostar M6VCT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Chapter 2 BIOS Setup 2.11 Set Supervisor/User Password Figure 10. Set Supervisor/User Password CMOS Setup Utility-Copyright (C ) 1984-1999 Award Software Standard CMOS Features Frequency Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Integrated Peripherals Set Supervisor Password Set User Password Power ManagementESnetuepr Password : Save & Exit Setup PnP/PCI Configurations PC Health Status Exit Without Saving Esc : Quit F9: Menu in BIOS F10 : Save & Exit Setup : Select Item Change / Set / Disable Password When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD Type the password, up to eight characters, and press . The password you type now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press . You may also press to abort the selection and not enter a password. To disable password, just press when you are prompted to enter password. A message will confirm that you wish to disable the password. Once the password is disabled, the system will boot and you can enter setup freely. 2-35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Chapter 2
BIOS Setup
2-35
2.11 Set Supervisor/User Password
±
Figure 10. Set Supervisor/User Password
CMOS Setup Utility-Copyright (C ) 1984-1999 Award Software
Standard CMOS Features
Frequency Control
Advanced BIOS Features
Load Optimized Defaults
Advanced Chipset Features
Set Supervisor Password
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Esc : Quit
F9: Menu in BIOS
: Select Item
F10 : Save & Exit Setup
Change / Set / Disable Password
When you select this function, the following message will appear at the center of
the screen to assist you in creating a password.
ENTER PASSWORD
Type the password, up to eight characters, and press <
Enter
>. The password you
type now will clear any previously entered password from CMOS memory. You
will be asked to confirm the password. Type the password again and press
<
Enter
>. You may also press <
ESC
> to abort the selection and not enter a
password. To disable password, just press <
Enter
> when you are prompted to
enter password. A message will confirm that you wish to disable the password.
Once the password is disabled, the system will boot and you can enter setup
freely.
Enter Password :