Bissell PowerLifter PowerBrush Upright Carpet Cleaner 1622 User Guide - Page 7

Page 7 highlights

Operation Carpet cleaning strokes 1. Plug the deep cleaner into a proper outlet and turn the power switch ON ( I ). The switch is located on the back of the unit. Tip: Thorough vacuuming before deep cleaning will prevent early clogging of the lint trap. 2. With your foot, press the handle release lever on the back of the lower body of unit. 3. While pressing the spray trigger, make one slow forward wet pass and another back. Let the BISSELL 2X advanced deep cleaning formula and DirtLifter PowerBrush do the work for you. Caution: Do not over wet. 4. Release the spray trigger and make one slow forward and backward pass over the same area to remove any residual dirty water and aid in drying. 5. Repeat cleaning passes until solution being pulled up appears clean. Continue passes without pressing the trigger until you can't see any more water being suctioned up. WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner. Non-BISSELL cleaning solutions may harm the machine and void the warranty. Empty the 2-in-1 water tank/ clean removable nozzle 1. Turn power switch OFF (O). Remove the 2-in-1 1. 2. water tank from the base using the tank carry handle. Carry the tank like a bucket to a utility sink or outside where you will dispose of the collection water. Remove the top of the tank by rotating the handle toward the back of the tank to unlatch lid and lift lid off tank. 2. Empty collection water from bottom of tank. Lint Screen 3. 4. 3. After each use, remove and rinse the lint screen located on the tank lid. 4. If nozzle needs to be rinsed: remove by grasping handle at top and pulling forward. Clean removable nozzle by rinsing under running water. 5. When finished replace nozzle by slightly raising front of machine to line up slots on the base of the machine with the hooks on nozzle. 5. Attach at base first and then click nozzle into place. NOTE: If nozzle is not attached properly loss, of suction will occur. 6. To continue carpet cleaning refer back to pages 6 through 8, beginning with "Fill the 2-in-1 water tank" on page 6. www.bissell.com 800.237.7691 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
O
peration
7
www.bissell.com
800.237.7691
Carpet cleaning strokes
1.
Plug the deep cleaner into a proper outlet
and turn the power switch ON
(I)
. The
switch is located on the back of the unit.
2.
With your foot, press the handle release
lever on the back of the lower body of unit.
3.
While pressing the spray trigger, make one
slow forward wet pass and another back.
Let the BISSELL 2X advanced deep cleaning
formula and DirtLifter PowerBrush do the
work for you.
Caution: Do not over wet.
4.
Release the spray trigger and make one
slow forward and backward pass over the
same area to remove any residual dirty
water and aid in drying.
5.
Repeat cleaning passes until solution being
pulled up appears clean. Continue passes
without pressing the trigger until you can’t
see any more water being suctioned up.
1.
Turn power switch OFF
(O)
.
Remove the 2-in-1
water tank from the base using the tank carry
handle. Carry the tank like a bucket to a utility sink
or outside where you will dispose of the collection
water. Remove the top of the tank by rotating the
handle toward the back of the tank to unlatch lid
and lift lid off tank.
2.
Empty collection water from bottom of tank.
3.
After each use, remove and rinse the lint
screen located on the tank lid.
4.
If nozzle needs to be rinsed: remove by grasping
handle at top and pulling forward. Clean removable
nozzle by rinsing under running water.
5.
When finished replace nozzle by slightly rais-
ing front of machine to line up slots on the
base of the machine with the hooks on nozzle.
Attach at base first and then click nozzle into
place.
NOTE: If nozzle is not attached properly
loss, of suction will occur.
6.
To continue carpet cleaning refer back to
pages 6 through 8, beginning with “Fill the
2-in-1 water tank” on page 6.
Tip:
Thorough vacuuming
before deep cleaning will prevent
early clogging of the lint trap.
WARNING:
To reduce the risk of fire
and electric shock due to
internal component
damage, use only BISSELL
cleaning fluids intended for
use with the deep cleaner.
Non-BISSELL cleaning
solutions may harm the
machine and void
the warranty.
Empty the 2-in-1 water tank/ clean removable nozzle
2.
3.
1.
5.
Lint Screen
4.