Home » Brother International Manuals » Sewing Machines » Brother International BAS-311F-L » Manual Viewer

Brother International BAS-311F-L Instruction Manual - English - Page 23

Installing the programmer (option), 3-17. Installing the work clamp lifter connecting rod

Get Brother International BAS-311F-L PDF manuals and user guides

View all Brother International BAS-311F-L manuals

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

3. INSTALLATION 3-16. Installing the programmer (option) [Vertical] [Flat] (2) (1) (1) (2) 1181S 1182S (4) (3) 1183S 1. Install the programmer support (2) to the work table with the two screws (1). 2. Insert the programmer connector (4) securely into the left side of the operation panel (3). 3-17. Installing the work clamp lifter connecting rod (BAS-311F-0 solenoid type only) (3) (5) (1) (7) (5) (3) (4) (6) (2) (8) 1184S 1185S 1. Remove the four screws (1), and then remove the side cover (2). 2. Install the work clamp lifter connecting rod (4) to the screw (3) on the work clamp lifter lever (5). 3. After installing, re-install the side cover (2) with the four screws (1). Note Remove chain hooking back (7) which is attached to the work clamp lifter pedal (6) before tilting back the machine head. Move the treadle support base (8) back and forth to adjust so that the chain which is attached to the presser lifter connecting rod (4) and the presser lifter treadle (6) does not touch the cables. BAS-311F-0, 311F-L, 326F-0 16

Section	Page
cover	1
PL	2
contents	6
1. NAME OF MAJOR PARTS	8
2. SPECIFICATIONS	9
3. INSTALLATION	10
3-1. Table processing diagram	11
3-2. Positioning	11
3-3. Installing the control box	12
3-4. Installing the rubber cushions	13
3-5. Installing the oil pan	13
3-6. Installing the cushions	14
3-7. Installing the switching plate	14
3-8. Installing the machine head	15
3-9. Tilting the sewing machine head	16
3-10. Connecting the ground wire	18
3-11. Connecting the cords (Installing the operation panel)	18
3-12. Installing the belt cover	21
3-13. Installing the foot switch	21
3-14. Installing the spool stand	21
3-15. Installing the eye guard	22
3-16. Installing the programmer (option)	23
3-17. Installing the work clamp lifter connecting rod	23
3-18. Installing the feed base cover supports	24
3-19. Installing the X feed base cover	24
3-20. Connecting the tubes (pneumatic type only)	25
3-20-1. Installing the air unit	26
3-20-2. Adjusting the speed controller	26
4. LUBRICATION	27
5. CORRECT OPERATION	28
5-1. Selecting the needle and thread	28
5-2. Installing the needle	28
6. USING THE OPERATION PANEL	33
6-1. Explanation of panel	33
6-2. Using the floppy disk	35
6-3. Using the program R/W (Read/Write) switch	37
6-4. Using the TEST switch (Checking the sewing pattern)	38
6-5. Using the emergency stop switch	39
6-6. Adjusting the sewing SPEED control	40
6-7. Changing the X-SCALE and Y-SCALE settings	40
6-8. Using the bobbin thread counter	41
6-9. Using production counter	42
6-10. Using single split mode	43
6-11. Shifting a stitch pattern	44
7. SEWING	45
7-1. Before starting sewing....	45
7-2. Sewing operation	45
8. CLEANING AND INSPECTION	47
8-1. Cleaning the rotary hook	47
8-2. Lubrication	47
8-3. Draining the oil	47
8-4. Cleaning the control box air inlet port	48
8-5. Cleaning the air holes of belt cover and frame side cover	48
8-6. Cleaning the eye guard	48
8-7. Checking the needle	48
9. STANDARD ADJUSTMENTS	49
9-1. Adjusting the needle bar height	49
9-2. Adjusting the needle bar lift amount	49
9-3. Adjusting the needle clearance	50
9-4. Adjusting the driver needle guard	50
9-5. Adjusting the shuttle race thread guide	50
9-6. Adjusting the movable knife	51
9-7. Adjusting the presser foot	53
9-8. Changing the presser foot lift	54
9-9. Adjusting the wiper	55
9-10. Adjusting the two-step work clamp lift amount	56
9-10-1. BAS-311F-0 Solenoid type	56
9-10-2. BAS-311F-0, 311F-L Pneumatic type	56
9-10-3. BAS-326F-0	57
9-10-4. Adjusting the air pressure	57
9-11. Adjusting the needle up stop position	58
9-12. Checking the input sensor and DIP switch input	59
9-13. Checking the input voltage	60
9-14. Clearing all memory settings	60
10. DIP SWITCH	61
10-1. Panel DIP switch functions	61
10-2. DIP switches inside the control box	63
11. CHANGING SPECIAL FUNCTIONS AND USING THE MEMORY SWITCHES	65
12. ERROR CODES	70
13. GAUGE PARTS LIST ACCORDING TO SUBCLASSES	73
14. TROUBLESHOOTING	75
15. OPTIONS	79