Brother International BAS-311F-L Instruction Manual - English - Page 71

Change program No.., Turn off power and check

Get Brother International BAS-311F-L PDF manuals and user guides View all Brother International BAS-311F-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

12. ERROR CODES Code Cause Remedy E.40 Floppy disk is not inserted or operation panel cable Insert a floppy disk. If floppy disk is already inserted, is not securely connected. turn off the power and check the connections of cords inside the operation panel. E.41 Invalid program No., or no data. Change program No.. E.43 E.4F E.50 E.51 E.52 E.5F E.60 Different floppy disk! Error occurred during floppy disk data reading. Floppy disk is write-protected. Insufficient available memory on floppy disk. Can not format this floppy disk. Error occurred during data writing on floppy disk. Can not backup data. (Panel PCB) Use original floppy disk. Replace the floppy disk and repeat the operation. Release write-protection. Use another floppy disk. Change floppy disk. Replace the floppy disk and repeat the operation. Turn off power and then clear all of the memory setting. E.61 Can not backup data. (Control PCB) Turn off power and then clear all of the memory setting. E.62 Operation panel error. Turn off power and then on again. E.63 Combination of control PROM and operation panel Turn off power and check it PROM is invalid. E.70 Same optional output number already exists. Change optional output number. If not use optional output, turn off power and then clear all of the memory setting. E.71 Bobbin changer error! - E.74 See the manual for bobbin changer. If not using the bobbin changer, set memory switch 23 to OFF. E.75 Milling motor has stopped due to overload. E.80 Upper thread has broken. (Rotary type sensor) See the manual for Milling motor. If not use milling motor, set OFF memory switch 10. Thread upper thread again. You can start sewing again. E.81 Upper thread has broken. (Optical fiber type sensor) Thread upper thread again. You can start sewing again. E.90 Power supply voltage is extremely low. Turn off power and check voltage. E.91 Power supply voltage is extremely high. Turn off power and check voltage. BAS-311F-0, 311F-L, 326F-0 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
12. ERROR CODES
BAS-311F-0, 311F-L, 326F-0
64
Code
Cause
Remedy
E.40
Floppy disk is not inserted or operation panel cable
is not securely connected.
Insert a floppy disk. If floppy disk is already inserted,
turn off the power and check the connections of cords
inside the operation panel.
E.41
Invalid program No., or no data.
Change program No..
E.43
Different floppy disk!
Use original floppy disk.
E.4F
Error occurred during floppy disk data reading.
Replace the floppy disk and repeat the operation.
E.50
Floppy disk is write-protected.
Release write-protection.
E.51
Insufficient available memory on floppy disk.
Use another floppy disk.
E.52
Can not format this floppy disk.
Change floppy disk.
E.5F
Error occurred during data writing on floppy disk.
Replace the floppy disk and repeat the operation.
E.60
Can not backup data. (Panel PCB)
Turn off power and then clear all of the memory setting.
E.61
Can not backup data. (Control PCB)
Turn off power and then clear all of the memory setting.
E.62
Operation panel error.
Turn off power and then on again.
E.63
Combination of control PROM and operation panel
PROM is invalid.
Turn off power and check it
E.70
Same optional output number already exists.
Change optional output number.
If not use optional output, turn off power and then clear
all of the memory setting.
E.71
-
E.74
Bobbin changer error!
See the manual for bobbin changer.
If not using the bobbin changer, set memory switch 23
to OFF.
E.75
Milling motor has stopped due to overload.
See the manual for Milling motor.
If not use milling motor, set OFF memory switch 10.
E.80
Upper thread has broken. (Rotary type sensor)
Thread upper thread again.
You can start sewing
again.
E.81
Upper thread has broken. (Optical fiber type sensor)
Thread upper thread again.
You can start sewing
again.
E.90
Power supply voltage is extremely low.
Turn off power and check voltage.
E.91
Power supply voltage is extremely high.
Turn off power and check voltage.