Brother International BAS-311F-L Instruction Manual - English - Page 24

Installing the feed base cover supports, BAS-311F-0, 311F-L, 326F-0

Get Brother International BAS-311F-L PDF manuals and user guides View all Brother International BAS-311F-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

3-18. Installing the feed base cover supports (BAS-311F-L, 326F-0) 3. INSTALLATION BAS-311F-L Coinside Coinside BAS-326F-0 Coinside (2) (3) (2(2) ) (2) (1) (1) 11116688SS 1169S 1186S Loosen the four screws (1) on the side of the bed by about 2-3 turns, and then install the feed base cover supports (2) to the side of the bed so that the top surfaces of the feed base cover supports (2) (one each at left and right) are at the same height as the top surfaces of the X and Y feed base covers (3) (at left and right). 3-19. Installing the X feed base cover (BAS-311F-L, 326F-0) 1166S BAS-311F-L BAS-326F-0 1167S (1) (2) (2) (3) A (1) (2) (3) (4) 1187S BAS-311F-L Loosen the four screws (1) by about 2-3 turns, slide the X feed base cover (2) (one each at left and right) in the direction of the arrow in the illustration, and then tighten the screws (1). BAS-326F-0 1. Loosen the four screws (2) which are holding the bellows (1) by about 2-3 turns, and then slide the X feed base cover assemblies (3) (one each at left and right) in the direction of the arrow in the illustration into the gaps (section A) between the needle plate support plate and the X and Y feed base cover (at left and right). 2. Lift the bellows (1) up slightly, clamp the tops and bottoms of the X feed base cover assemblies (3) (one each at left and right) between the bellows (1) and the X feed base (4) and the then tighten the screws (2). BAS-311F-0, 311F-L, 326F-0 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
3. INSTALLATION
BAS-311F-0, 311F-L, 326F-0
17
3-18. Installing the feed base cover supports
(BAS-311F-L, 326F-0)
Loosen the four screws (1) on the side of the bed by about 2-3 turns, and then install the feed base cover supports (2) to
the side of the bed so that the top surfaces of the feed base cover supports (2) (one each at left and right) are at the same
height as the top surfaces of the X and Y feed base covers (3) (at left and right).
3-19. Installing the X feed base cover
(BAS-311F-L, 326F-0)
BAS-311F-L
Loosen the four screws (1) by about 2-3 turns, slide the X feed base cover (2) (one each at left and right) in the direction
of the arrow in the illustration, and then tighten the screws (1).
BAS-326F-0
1. Loosen the four screws (2) which are holding the bellows (1) by about 2-3 turns, and then slide the X feed base cover
assemblies (3) (one each at left and right) in the direction of the arrow in the illustration into the gaps (section A)
between the needle plate support plate and the X and Y feed base cover (at left and right).
2. Lift the bellows (1) up slightly, clamp the tops and bottoms of the X feed base cover assemblies (3) (one each at left
and right) between the bellows (1) and the X feed base (4) and the then tighten the screws (2).
1168S
BAS-311F-L
BAS-326F-0
BAS-311F-L
(1)
1187S
BAS-326F-0
(2)
(3)
(2)
(1)
(2)
(3)
(4)
1167S
1166S
A
1168S
(1)
(2)
Coinside
BAS-311F-L
(1)
(2)
Coinside
BAS-326F-0
(2)
(3)
Coinside
1169S
1186S