Brother International BAS-326E Network Users Manual - English - Page 47

Upper shaft mechanism, against the crank of the upper shaft

Get Brother International BAS-326E PDF manuals and user guides View all Brother International BAS-326E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

6. Upper shaft mechanism Chapter 3. Assembly e q w t y r e q i o !1 !0 y !1 u t q r 0.5mm !0 q w !0 i 1. Insert the upper shaft q from the rear of the machine, and place the thread trimmer cam w and the stepping work clamp connecting rod e on the shaft. * Apply adhesive (equivalent of Three Bond 1401) around the area which the bearing in the machine goes into. Also, apply grease to grooves on the thread trimmer cam w. 2. Pass the thread take-up crank r from the face plate side over the upper shaft q, and tighten the screw t and the set screw y. 3. Place the upper shaft bush between the thread take-up crank r and the stepping work clamp connecting rod e, and secure the upper shaft q so that there is no looseness. (At this time, do not securely tighten the set screw of the stepping work clamp conncting rod e.) 4. Press the thread trimmer conncting rod w against the crank of the upper shaft q. Adjust the set screw u that comes first when rotating to the screw flat, and tighten it. 5. Attach they synchronizer i to the machine using the screw o. 6. Attach the pulley !0 leaving a 0.5 mm clearance from the protrusion of the synchronizer i, tighten the set screw !1 that comes later when rotating to the screw flat. BAS-311E.311EL.326E.326EL 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
39
BAS-311E.311EL.326E.326EL
Chapter 3. Assembly
6. Upper shaft mechanism
1.
Insert the upper shaft
q
from the rear of the machine, and place the thread trimmer cam
w
and the stepping work
clamp connecting rod
e
on the shaft.
*
Apply adhesive (equivalent of Three Bond 1401) around the area which the bearing in the machine goes into. Also,
apply grease to grooves on the thread trimmer cam
w
.
2.
Pass the thread take-up crank
r
from the face plate side over the upper shaft
q
, and tighten the screw
t
and the set
screw
y
.
3.
Place the upper shaft bush between the thread take-up crank
r
and the stepping work clamp connecting rod
e
, and
secure the upper shaft
q
so that there is no looseness.
(At this time, do not securely tighten the set screw of the
stepping work clamp conncting rod
e
.)
4.
Press the thread trimmer conncting rod
w
against the crank of the upper shaft
q
. Adjust the set screw
u
that comes
first when rotating to the screw flat, and tighten it.
5.
Attach they synchronizer
i
to the machine using the screw
o
.
6.
Attach the pulley
!
0
leaving a 0.5 mm clearance from the protrusion of the synchronizer
i
, tighten the set screw
!
1
that
comes later when rotating to the screw flat.
i
q
e
!
1
!
0
y
t
r
!
0
w
q
q
w
u
q
e
y
t
r
o
!
1
i
!
0
0.5mm