Brother International BAS-326E Network Users Manual - English - Page 62

Adjustment of air pressure for Pneumatic type 311E, 311EL, 326E, 326EL, 2. Pneumatic type

Get Brother International BAS-326E PDF manuals and user guides View all Brother International BAS-326E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Chapter 4. Adjustments 6-2. Pneumatic type (BAS-311E · 311EL) e w q (BAS-326E · 326EL) y y w r w e r r 20mm e e w t r 20mm t 1. Turn on the air, and then press the work clamp lifter switch q while turning it clockwise, to raise the work clamp w. 2. Loosen the bolts r of work clamp arm lever F e (BAS-326E, 326EL: work clamplifter lever y). 3. Place a ruler against the work clamp w, and then move work clamp arm lever F e (BAS-326E, 326EL: work clamplifter lever y) vertically to find the position where the lift amount of the work clamp is 20 mm. 4. After adjusting the lift amount to 20 mm, tighten the bolts r of work clamp arm lever F e(BAS-326E, 326EL: work clamplifter lever y). 6-3. Adjustment of air pressure (for Pneumatic type 311E, 311EL, 326E, 326EL) 1. Air pressure should be 0.49 MPa [5 kgf /cm2]. The air pressure can be adjusted by pulling up and turn- ing the control knob w on the integrator q. After adjustment is complete, push the control knob w downward to lock it. w r 2. If water stands in the bottle of the integrator q, turn the drain cock e in the direction indicated by an arrow to drain the water. Note: Open the air cock r slowly. q e 54 BAS-311E.311EL.326E.326EL

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
54
BAS-311E.311EL.326E.326EL
Chapter 4. Adjustments
6-3. Adjustment of air pressure (for Pneumatic type 311E, 311EL, 326E,
326EL)
1.
Air pressure should be 0.49 MPa [5 kgf /cm
2
].
The air pressure can be adjusted by pulling up and turn-
ing the control knob
w
on the integrator
q
.
After adjustment is complete, push the control knob
w
downward to lock it.
2.
If water stands in the bottle of the integrator
q
, turn the
drain cock
e
in the direction indicated by an arrow to
drain the water.
Note:
Open the air cock
r
slowly.
6-2. Pneumatic type
1.
Turn on the air, and then press the work clamp lifter switch
q
while turning it clockwise, to raise the work clamp
w
.
2.
Loosen the bolts
r
of work clamp arm lever F
e
(BAS-326E, 326EL: work clamplifter lever
y
).
3.
Place a ruler against the work clamp
w
, and then move work clamp arm lever F
e
(BAS-326E, 326EL: work clamplifter
lever
y
) vertically to find the position where the lift amount of the work clamp is 20 mm.
4.
After adjusting the lift amount to 20 mm, tighten the bolts
r
of work clamp arm lever F
e
(BAS-326E, 326EL: work
clamplifter lever
y
).
(BAS-311E · 311EL)
(BAS-326E · 326EL)
q
w
e
r
w
e
t
r
20mm
y
y
w
r
w
e
e
r
t
20mm
w
r
q
e