Brother International BM2800 Users Manual - English and Spanish - Page 15

Caution

Get Brother International BM2800 PDF manuals and user guides View all Brother International BM2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

1 1 Pull the thread in completely. 1 2 3 1 Pre-tension disk 2 Bobbin winder shaft 3 Bobbin Pull up the spool pin and put a spool of 1 thread on this pin. Put the bobbin onto the bobbin winder 4 shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the notch of the bobbin. • Make sure to pull out 7 to 10 cm (3-4 inches) of thread from the hole on the bobbin. While holding the thread from the spool 2 with your right hand, pass the thread toward you, in the groove on the thread guide. Then, pass the thread around the pre-tension disk and pull the thread in completely. 3 1 2 1 1 Pre-tension disk CAUTION ● If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin. Pass the end of the thread through the 3 hole on the bobbin from the inside of the bobbin. 1 Spring on the shaft 2 Notch 3 7-10 cm (3-4 inches) CAUTION ● Pull the thread taut and hold the end of the thread straight up. If the thread is too short, not pulled taut or held at an angle, injuries may occur when the thread is wound around the bobbin. Turn on the machine. 5 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
14
————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————
1
1
Pull up the spool pin and put a spool of
thread on this pin.
2
While holding the thread from the spool
with your right hand, pass the thread
toward you, in the groove on the thread
guide. Then, pass the thread around the
pre-tension disk and pull the thread in
completely.
1
Pre-tension disk
CAUTION
3
Pass the end of the thread through the
hole on the bobbin from the inside of the
bobbin.
4
Put the bobbin onto the bobbin winder
shaft and slide the bobbin winder shaft to
the right. Turn the bobbin clockwise, by
hand, until the spring on the shaft slides
into the notch of the bobbin.
•
Make sure to pull out 7 to 10 cm (3-4 inches)
of thread from the hole on the bobbin.
1
Spring on the shaft
2
Notch
3
7-10 cm (3-4 inches)
CAUTION
5
Turn on the machine.
1
Pre-tension disk
2
Bobbin winder shaft
3
Bobbin
1
3
2
1
Pull the thread
in completely.
●
If the spool of thread is in the wrong
place, or is set incorrectly, the thread
may tangle on the spool pin.
1
●
Pull the thread taut and hold the end of
the thread straight up. If the thread is too
short, not pulled taut or held at an angle,
injuries may occur when the thread is
wound around the bobbin.
3
1
2