Brother International Innov-is VM5100 Installation Guide for Premium Pack I Op - Page 8

If an error message appears, Certify, Finish, USB media, computer

Get Brother International Innov-is VM5100 PDF manuals and user guides View all Brother International Innov-is VM5100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

i Type in the internal machine identification number (No.) written down in step a, and then click "Next". k Write down the 8-digit Certification Key that appears. If an error message appears Check that symbols or characters other than numbers have not been entered. To close the message, click "OK". Note • After upgrading the sewing machine to KIT I, the Certification Key must be entered in the sewing machine Settings screen. j Carefully verify that the information has been entered correctly and then click "Certify". l Click "Finish". The certification key has been successfully obtained. Now proceed to installing the upgrade application for KIT I on the sewing machine. Memo • To change the entered information, click "Back". Use USB media or a computer to install the upgrade application. If USB media is to be used, refer to the instructions that follow. If a computer is to be used, refer to the procedure described on page 8. If an error message appears Check below list for possible error(s). To close the message, click "OK". • Verify that the CD key and internal machine identification number (No.) have been entered correctly, and then repeat the procedure from step c. • The CD Key is valid for use with only one designated internal machine identification number (No.). Check that the CD key has been entered correctly, and then repeat the procedure from step c. • Check the Internet connection, and then click "Certify" again. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
6
i
Type in the internal machine identification
number (No.) written down in step
a
, and
then click
“Next”
.
If an error message appears
Check that symbols or characters other than
numbers have not been entered. To close the
message, click
“OK”
.
j
Carefully verify that the information has been
entered correctly and then click
“Certify”
.
If an error message appears
Check below list for possible error(s). To close
the message, click
“OK”
.
• Verify that the CD key and internal machine
identification number (No.) have been entered
correctly, and then repeat the procedure from step
c
.
• The CD Key is valid for use with only one
designated internal machine identification number
(No.). Check that the CD key has been entered
correctly, and then repeat the procedure from step
c
.
• Check the Internet connection, and then click
“Certify” again.
k
Write down the 8-digit Certification Key that
appears.
l
Click
“Finish”
.
The certification key has been successfully obtained.
Now proceed to installing the upgrade application for
KIT
I
on the sewing machine.
Use USB media or a computer to install the upgrade
application.
If
USB media
is to be used, refer to the instructions that
follow.
If a
computer
is to be used, refer to the procedure
described on page 8.
Memo
•
To change the entered information, click
“Back”
.
Note
•
After upgrading the sewing machine to KIT
I
, the
Certification Key must be entered in the sewing
machine Settings screen.