Brother International SM-6500PRW Users Manual - English - Page 41

Pull the upper thread at the end of

Get Brother International SM-6500PRW PDF manuals and user guides View all Brother International SM-6500PRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Place a button between the presser foot and d the fabric. Turn the handwheel toward you h (counterclockwise) to check that the needle correctly goes into the two holes of the button. Adjust the stitch width to the distance between the button holes. • When attaching four-hole buttons, first sew the two holes closest to you. Then, slide the button so that the needle goes into the two holes toward the rear of the sewing machine, and then sew them in the same way. 3 Select a stitch . (With models not provided e with stitch , select stitch .) Adjust the stitch width so that it is the same as f the distance between the holes in the button. Set the stitch length to the shortest setting by g pressing the stitch length adjustment key. CAUTION ● When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. Start sewing. i • After sewing for about 10 seconds at low speed, press (reverse/reinforcement stitch button) to sew reinforcement stitches. Pull the upper thread at the end of the j stitching to the wrong side of the fabric, and then tie it with the bobbin thread. Use scissors to cut the upper thread and the bobbin thread at the beginning of the stitching. When you are finished attaching the button, k slide the feed dog position lever to (to the left as seen from the front of the machine) to raise the feed dogs. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
39
3
d
Place a button between the presser foot and
the fabric.
• When attaching four-hole buttons, first sew
the two holes closest to you. Then, slide the
button so that the needle goes into the two
holes toward the rear of the sewing machine,
and then sew them in the same way.
e
Select a stitch
. (With models not provided
with stitch
, select stitch
.)
f
Adjust the stitch width so that it is the same as
the distance between the holes in the button.
g
Set the stitch length to the shortest setting by
pressing the stitch length adjustment key.
h
Turn the handwheel toward you
(counterclockwise) to check that the needle
correctly goes into the two holes of the
button.
Adjust the stitch width to the distance between
the button holes.
i
Start sewing.
• After sewing for about 10 seconds at low
speed, press
(reverse/reinforcement stitch
button) to sew reinforcement stitches.
j
Pull the upper thread at the end of the
stitching to the wrong side of the fabric, and
then tie it with the bobbin thread.
Use scissors to cut the upper thread and the
bobbin thread at the beginning of the stitching.
k
When you are finished attaching the button,
slide the feed dog position lever to
(to
the left as seen from the front of the machine)
to raise the feed dogs.
●
When sewing, be sure that the needle does
not touch the button, otherwise the needle
may bend or break.
CAUTION