Canon 3060 Startup Guide - Page 21

SCSI ID and Terminator Settings

Get Canon 3060 - DR - Document Scanner PDF manuals and user guides View all Canon 3060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

SCSI ID and Terminator Settings Use the DIP switches on the rear of the scanner to make the SCSI ID and terminator settings. For the DIP switches, the upper position is the ON position, and the lower position is the OFF position. Factor settings (Terminator: OFF; SCSI ID = 2) ON1 2 3 4 SCSI ID switches Terminator ON/OFF switch SCSI ID Settings Refer to the following table when setting the SCSI ID. If there are other SCSI devices connected to or inside the PC, make sure to set a unique ID for the scanner. SCSI ID 0 1 2 3 4 5 6 7 SW2 OFF OFF OFF OFF ON ON ON ON SW3 OFF OFF ON ON OFF OFF ON ON SW4 OFF ON OFF ON OFF ON OFF ON Notice When the scanner is shipped from the factory, the SCSI ID is set to "2." Although any value from 0 to 7 is valid as a SCSI ID, "7" is normally reserved for the SCSI host adapter, and should therefore not be used. In addition, "0" and "1" are normally used by internal SCSI hard disks that are used for system startup, so do not use these IDs either. Installing the Scanner 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Installing the Scanner
17
SCSI ID and Terminator Settings
Use the DIP switches on the rear of the scanner to make the SCSI ID and
terminator settings.
For the DIP switches, the upper position is the ON position, and the lower
position is the OFF position.
1
ON
234
SCSI ID switches
Terminator ON/OFF switch
Factor settings
(Terminator: OFF; SCSI ID = 2)
SCSI ID Settings
Refer to the following table when setting the SCSI ID. If there are other SCSI
devices connected to or inside the PC, make sure to set a unique ID for the
scanner.
SCSI ID
SW2
SW3
SW4
0
OFF
OFF
OFF
1
OFF
OFF
ON
2
OFF
ON
OFF
3
OFF
ON
ON
4
ON
OFF
OFF
5
ON
OFF
ON
6
ON
ON
OFF
7
ON
ON
ON
Notice
When the scanner is shipped from the factory, the SCSI ID is set to "2."
Although any value from 0 to 7 is valid as a SCSI ID, "7" is normally reserved
for the SCSI host adapter, and should therefore not be used. In addition, "0"
and "1" are normally used by internal SCSI hard disks that are used for system
startup, so do not use these IDs either.