Cisco WS-X4013 Hardware Maintenance Manual - Page 106

If you are done with all SIMM replacement procedures, proceed to the Replacing Network

Get Cisco WS-X4013 - Supervisor Engine II-Plus-TS PDF manuals and user guides
UPC - 746320976914
View all Cisco WS-X4013 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Memory Replacement Procedures Figure 5-9 Installing Main Memory SIMMs Top view Front of the chassis 1. Insert the SIMM into the socket at an angle 45° from vertical. 2. Push the SIMM down and back. 3. The socket guide posts insert through the SIMM holes (on both sides). 4. The locking spring will clip the back of the SIMM when it is fully installed (on both sides). Polarization notch Side view 1. Insert the SIMM into the socket at an angle 45° from vertical. 3. The socket guide posts insert through the SIMM holes (on both sides). 4. The locking spring will clip the back of the SIMM when it is fully installed (on both sides). 2. Push the SIMM down and back. H1152 Caution You will feel some resistance, but do not use excessive force on the SIMM and do not touch the surface components to avoid damaging them. Step 6 Repeat Steps 2 through 5 for each main memory SIMM. If you are done with all SIMM replacement procedures, proceed to the section "Replacing Network Processor Modules" later in this chapter. 5-12 Cisco 4000 Series Hardware Installation and Maintenance

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
5-12
Cisco 4000 Series Hardware Installation and Maintenance
Memory Replacement Procedures
Figure 5-9
Installing Main Memory SIMMs
Caution
You will feel some resistance, but
do not use excessive force on the SIMM and do not touch
the surface components to avoid damaging them.
Step 6
Repeat Steps 2 through 5 for each main memory SIMM.
If you are done with all SIMM replacement procedures, proceed to the section “Replacing Network
Processor Modules” later in this chapter.
2. Push the SIMM down and back.
1. Insert the SIMM into the socket at an angle 45
°
from vertical.
The socket guide posts insert
through the SIMM holes
(on both sides).
3.
The locking spring will
clip the back of the SIMM
when it is fully installed
(on both sides).
4.
H1152
Top view
Front of the chassis
Polarization
notch
1. Insert the SIMM into the socket at an angle 45
°
from vertical.
The socket guide posts insert
through the SIMM holes
(on both sides).
3.
The locking spring will
clip the back of the SIMM
when it is fully installed
(on both sides).
4.
Side view
2. Push the SIMM down and back.