Clifford Concept 400 Owners Guide - Page 5

TO TURN VALET Press the master remote LevelShift button twice, then button 1 or press buttons MODE ON OR OFF: valet mode. and ✱ (companion remote) to enable/exit TO REMOTELY OPEN If you have this option, press the master remote LevelShift button once, then button 2 or press buttons and OR VENT WINDOWS: (companion remote) after disarming to fully open the windows controlled by SmartWindows 4. On hot days, press this button combination right after arming to vent the windows slightly while the system remains armed. OTHER FEATURES AND OPTIONS: Other system features and options can be accessed as noted in the following Quick Reference table: QUICK REFERENCE: REMOTE CONTROL FUNCTIONS Function Companion Remote Button(s) Master Remote LevelShift? Button Arm or disarm and lock or unlock the doors no 1 Optional wired accessory #1* (usually optional trunk release) no 2 Silently arm or disarm and lock or unlock the doors +✱ no 3 Unassigned or IntelliStart 4 accessory remote engine starting ✱ no 4 Parking Lot HighLight turns on parking lights for 10-seconds** 1 time 1 Unassigned or SmartWindows 4 accessory full open or post-arm venting* + 1 time 2 Optional wired accessory #3* (usually IntelliVoice 4 voice synthesis on/off) +✱ 1 time 3 Unassigned* + 1 time 4 Remote valet mode entry/exit +✱ 2 times 1 Remote override of the Dual-Zone Proximity Sensor 4 + 2 times 2 Unassigned or IntelliStart 4 LowTemp or LowBattery AutoStart, and manual transmission SafeStart 2 times 3 Unassigned* 2 times 4 Unassigned* 3 times 1 Unassigned* 3 times 2 Remotely adjust sensitivity of the optional Dual-Zone OmniSensor 3 times 3 Remotely adjust sensitivity of the Dual-Zone Proximity Sensor 4 3 times 4 * These buttons/channels can be assigned to control Clifford systems and accessories on your other vehicles. ** Not available on European models ACG 2 (Anti-CodeGrabbing 2™) ACG 2 protects you and your automobile from code-grabbing devices. Code-grabbers record, from hundreds of feet away, the code sent by your car alarm remote control (code-grabbers are very similar to, but simpler than, cellphone "cloning" devices). The thief then plays back the code when you're gone, instantly disarming the alarm and unlocking the doors. It's like leaving your keys and remote in the door. Many non-Clifford alarms can be defeated that easily, and some of the latest "smart" code-grabbers can even decipher the code hopping/jumping sequence used by other car alarm manufacturers. In contrast, your Concept 400 uses complex digital signal processing and unbreachable code encryption to randomly change the digital code every time you use the remote control. Your remotes will never transmit the same code twice, and the control unit will never accept the same code twice. Thus the code played back by the code-grabber - even the latest generation smart code-grabbers - will never be accepted by your Concept 400 system. Adding new remote controls For other drivers, or to control Clifford G4 systems on your other cars with the same remote, you can buy additional remote controls from any Clifford Dealer (or direct from the Customer Service Department of your nearest Clifford Headquarters listed on the front cover) and program them into the system yourself. Concept 400 will respond to as many as four remote controls. NOTE: Clifford G4 systems will respond only to G4-type ACG 2 remote controls. Older Clifford ACG and non-ACG remote controls are not compatible with G4 systems. To add a new master 5-button remote control, use the Add new master remote feature (column 1, row 1) of the User-selectable features table. To add a new companion 4-button remote, program each button and button combination to the specific functions noted in column 4. #