Clifford Concept 400 Owners Guide - Page 7

PlainView 2 Coded Valet Mode All car alarms have a valet mode that turns off the security features. This mode turns off the alarm if the system is not responding to the remote. However, thieves disable other alarms by flicking this easy-to-find "hidden" valet switch. In contrast, your system has safeguards that ensure a thief cannot enable the valet mode as a way of "turning off" your system. To enable valet mode, the driver must first enter the secret valet/disarming PIN (personal identification number) code - the same PIN code described in the BlackJax anti-carjacking section - on the PlainView 2 switch mounted on your vehicle's dash or console. When the system is in valet mode, it overrides AutoArming and all other security features, which is handy when refueling or washing your car. The system's factory-set valet/disarming PIN code is 2: ✱✱ blank. NOTE: If you temporarily lose the use of your remote controls, you can disarm the system by enabling valet mode. Entering a code To enter your PIN code, press the ✱ button the appropriate number of times on the PlainView 2 switch followed by the blank button. To enter a zero, you simply press the blank button. EXAMPLE: To enter a code of 1203, you would press: ✱ blank, ✱✱ blank, blank, ✱✱✱ blank. To enable valet mode 1. Turn the ignition switch to its "ON" position or start the engine if it is not already running. 2. Enter your valet/disarming PIN code on the PlainView 2 switch. 3. Continue pressing the blank button for 4 seconds. Release the button. The LED will continue to remain on for ongoing visual confirmation of valet mode. To exit valet mode and restore normal operation 1. Turn the ignition switch to its "ON" position or start the engine if it is not already running. 2. Enter your valet/disarming PIN code on the PlainView 2 switch. The LED will turn off. Remote Controlled Valet Mode Valet mode turns off all security features and prevents AutoArming when, for instance, having your car washed. To turn valet mode on/off, press the LevelShift button twice, then button 1 (master remote) or simultaneously press the ✱ and buttons (companion remote). Two parking light flashes confirm valet mode on, one flash confirms valet mode off. The dashboard LED will glow continuously when valet mode is on. Your system remains in valet mode until you again press this button combination to turn it off and restore normal operation. This is a user-selectable feature and may be programmed off if you wish to use this button combination for a different function. There is a slight security risk associated with remote controlled valet mode in that a carjacker familiar with Clifford systems could possibly engage valet mode via the remote control before the BlackJax anti-carjacking feature is triggered. Although this is an unlikely scenario, you may prefer to turn off valet mode entry/exit via the remote control using the User-selectable features programming (column 2, row 3). False Alarm Prevention & FACT™ With FACT (False Alarm Control and Test), you'll never experience repeated false alarms. If the siren sounds, DO NOT disarm; allow it to run for the full siren duration. Before sounding the siren a second time, the system automatically checks for another activated sensor or trigger to verify that an intrusion is in progress. This feature is user-selectable. High-Output Medallion Siren This Clifford-engineered siren is more rugged than generic sirens and has these features: n User-selectable chirp volume: You can control the volume of the arm and disarm chirps. From the factory, your system issues QuietChirps. If you prefer, you may select the full-volume LoudChirp acknowledgments. See User-selectable features. n Remote siren silencing: If triggered by a non-threatening event, you can silence the siren without remotely disarming. Press button 1 (master remote) or button (companion) while the siren is sounding. Two chirps confirm that the sensor activated the alarm and the system is remaining armed. Four chirps confirm that the system is still armed, but that the ignition is on or the hood, trunk or a door is open and that this may indeed be a genuine theft attempt. n Automatic noise abatement: Alarm sounding is limited to five siren duration cycles even if a door is left open in the wake of an intrusion. n Long-term chirp silencing: You may silence the arm and disarm chirps on a long-term basis until you decide to restore them. Your vehicle's parking light flashes will continue to provide visual confirmation of remote controlled system arming and disarming. See User-selectable features. n Selectable siren duration (non-European models only*): You may change the factory set 30-second siren duration to 60 or 90 seconds via the programming procedure or via the CliffNet Wizard software. See User-selectable features. n Personalized Siren Sounds (non-European models only*): The Medallion siren sounds six different alarm sounds. You may turn any of the six sounds on or off via the User-selectable features programming to create a different combination of sound patterns. So if you hear a siren at a distance, you will know for sure whether it is your car or someone else's. See User-selectable features (column 1, row 2). What's more, with the optional CliffNet Wizard software and DataPort Replicator Cable, you may select up to six sounds from more than a dozen different siren sound choices for truly unique customization. n Choose when your Personalized Siren Sounds* play: For more information at a distance, you may choose to have your Personalized Siren Sounds "play" every time the alarm is set off, or you may set them to sound them only upon trigger activation. When set to "trigger only" the basic siren wail will sound if a sensor is activated, but the Personalized Siren Sounds will play if the hood, trunk or a door is opened. See User-selectable features (column 1, row 3). *Not available on European models in compliance with EC95/56 %