Cobra MR HH450 MR HH450 DUAL Manual - English - Page 25

Intro VOHpFerMatainrigneYoRuardRioaPdirootocols Intro Operation Secondary Icons SCAN Button Enter Record Secondary Icons Installation Mic Recorder Main Icons Notice GMRS Intro MED SAME Mic Recorder ON Secondary Icons GMRS ain Icons MED SAME Operation Customer Assistance Warranty Advanced Operation InsCtaullasttioonmer Assistance CAsussitsotmaWnecarerranty Using Rewind-Say-Again® to Record VOICE Audio Transmission: NOTE CustomerIf the record memory is locked (rewind icon flashing), press and hold Assistance Notice Caution the REW Warning button to unlock. 1. Press and hold SCAN button for two (2) seconds to enter Record mode. The matrix will display MIC RECORDER. 2. Press and hold PTT button to begin recording from radio microphone. The transmitter will turn off. The Caution Warning matrix will display MIC RECORDER ON and the seconds remaining will be shown in the lower right corner. If PTT button is released, recording stops. While recording, a Operation 20-second Customer Assistance Wcaorruanntytdown begins on display. When 20-second countdown time has ended, recording stops and two (2) beep tones will be heard. Installation 3. PCruesstomserand hold SCAN button again for two (2) seconds pArsesisstasncMe EM/ESC button to cancel recording and return or to last operation. NOTE Please refer to the Bluetooth Mode Pairing and Notice Caution Warning Intro econdary Icons Tri-Watch Mode OTperria-tioWn atchCusmtomoerde givWeasrranytyou one (1) button access to scan Assistance a total of three (3) channels of most importance to you. Channel 16 is preprogrammed and will always be one (1) of the scanned locations. Two (2) other channels, either GMRS or VHF, of your choice can be Installation stored in Customer Assistance the radio. These channels can be edited and/or recalled during future engagements of Tri-Watch mode. NOTE The radio must be squelched for Tri-Watch mode to function. See page 18 for Notice SquCaeutliocn h procWeardninugre. 44 English Main Icons Advanced Operation VOHpFerMatainrigneYoRuardRioaPdirootocols Intro Tri-Watch Button Operation Intro Customer Warranty Tri-Watch Setup OperaAtisosnistance Customer Assistance Warranty To Program or Edit the Tri-Watch Channels: 1. Press and hold the TRI-WATCH button from Marine or GMRS Installation Standby mode Customer InstalAlastiosnistance Customer Assistance for two (2) seconds to activate Tri-Watch Setup Memory SLeocconadtaiorynIcNonusmSbeceorndary Icons ROG GVHMmwFRiolldSdei.sTphlaey MEM icon TW MEM on the display ENTER 01. will turn On and the matrix VHF TRX NOTE The main channel number will flash to indicate channel position. If U U A Notice NoticCeautiotnherCeauitsionnWoarinninpguWtaarncintgivity for 15 seconds, the radio will sound three (3) LO VOSRXAOMGE MGVEHMMFRHSI SAM2E. MbEeMeps and return to GMRS or Marine Standby mode. Use the Band button to select Marine or GMRS channels. Band Button TRX 3. Press Channel Up/Down button to select the desired Tri-Watch channel. U VOX HI SAME ROG MEM 4GV.HMPbFruRetSstosnatnodcroenlefiarsme TRI-WATCH entry. button or Call/Enter/Setup T5R.XRWeaptecaht steps 2 and 3 to program memory channel. the remaining additional Tri- U Channel Up/Down Buttons VOX Main Icons 6. After programming both Tri-Watch memory channels the radio HISAMEMwEilMl immediately engage Tri-Watch mode. Using Tri-Watch Tri-Watch Scan Mode: Tri-Watch Button 1. From Marine or GMRS Standby mode, press the TRI-WATCH button. The TW SCAN will display on the matrix along with the three Intro Operation chanCAsunssietsotmlasnecrse toredWianrratnhtye Tri-Watch memory. 2. The radio will scan through the three (3) Tri-Watch memory channels. Secondary Icons Tri-Watch Scan Mode 3. Installation A siCgunstoamleron Assistance any one (1) of the three (3) channels will stop the scan for 10 seconds to allow you to listen to the traffic on that location. U LO VHF A SAMEMEM NOTE After the Tri-Watch scan stops to monitor a channel, as long Notice as yCaouutiondo notWparrneinsg s any buttons within 10 seconds, your radio will automatically resume scanning the Tri-Watch channels. 4. Press the Channel Up/Down button to resume scanning the Tri-Watch channels or to change the scan direction. 5. To EXIT the Tri-Watch scan, press the TRI-WATCH button again, and the radio will return to Marine or GMRS Standby mode. Nothing Comes Close to a Cobra® 45