Cobra MR HH450 MR HH450 DUAL Manual - English - Page 27
Scan Modes, VHF Channel Scan, GMRS Scan, Memory Location Scan
View all Cobra MR HH450 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
Operating Your Radio Intro SCAN Button Operation Main Icons Secondary Icons Installation Intro Advanced Operation Customer Warranty Scan Assistance Modes A signal on any channel will stop the scan for 10 seconds to allow you to listen to the traffic on that location. After 10 sCeucstoomnedr s, the radio will resume scanning. PArsesisstasnctehe Channel Up/Down button to resume scanning before Operation Customer Warranty the 10-secAossnistdancpe ause has completed or to change the scan direction. Scan Display U LO U VOX Main Icons Notice Secondary Icons ROGVHGFMRS VHF A TRX SAME Intro HI SAME MEM Channel Up/Down Buttons Secondary Icons VHF Installation DCuaruitniogn ChCaustnomenr el Scan ChaAsnsisnWtaenacrleninSgcan mode, the radio will rapidly switch from channel to channel through all the channels. OpeNraottioicne NOTE The radio must be squelched for Channel Scan mode to function. CuCstaoumtieorn Assistance See page WWarararnntinyg 28 for Squelch procedure. To Enter Marine Scan: 1. From Marine or GMRS Standby mode, press the SCAN Installation button. Customer Assistance The radio will immediately begin to scan the entire channel map selected in the active channel map. CHANNEL SCAN will display on the matrix. Main Icons Main Icons Intro NOTE If Priority 16 feature has been selected, channel 16 will Notice cheCcauktioend frequWaernnintgly for activity to insure you will not miss any calls. 2. To EXIT Channel Scan mode, press the SCAN or PTT button again. The SCAN icon will disappear from the LCD and the radio will return to Marine or GMRS Standby mode. Operation Customer Assistance Warranty 48 English Intro Secondary Icons Secondary Icons Memory Location Scan During Memory Location Scan mode, Operation Installation CACsuusssittsootmmaneecrre Assistance Warranty the radio will rapidly scan through all pre-assigned memory channels. NOTE Installation Customer Assistance The radio must be squelched for Memory Location Scan Notice moCdauetiotno funcWtiaornning. See page 18 for Squelch procedure. NOTE If there are fewer than two (2) memory locations Notice proCgarutaiomn med Winarntinhg e radio, the Memory Location Scan option will not be available. To program at least two (2) memory locations, see page 34. Operating Your Radio Intro Operation MEM/ESC Button Secondary Icons Installation Memory Channel Scan VHNFotice U HI SAME MEM Advanced Operation Customer Warranty To Assistance Enter Memory Location Scan: 1. From Marine or GMRS Standby mode, press the MEM/ ESC button. 2. Customer Assistance Press the SCAN button. The radio will immediately begin to scan all pre-assigned memory channels. The MEM icon will show on the LCD, and MEM CHAN SCAN will display on the matrix along with the memory location. 3. To EXIT Memory Location Scan mode, press the SCAN or PTT button again. The MEM icon will disappear from Caution the LWCarDningand the radio will return to Marine or GMRS Standby mode. Scan All Schannels LO Scan CTCSS LO GMRS GMRS GMRS Scan In GMRS mode, there are 3 types of scans - all GMRS channels, CTCSS tones (on the selected channel) and DCS codes (on the selected channel). To Enter the GMRS Scans: 1. Successive press and release of the SCAN button will toggle betwen all channel scan, CTCSS tone scan and DCS code scan. 2. Press and hold the SCAN button to start the selected scan. 3. To exit a GMRS scan, press the MEM/ESC button or PTT. Scan DCS GMRS LO Nothing Comes Close to a Cobra® 49