Cub Cadet Pro Z 160L EFI Owners Manual
Cub Cadet Pro Z 160L EFI Manual
 |
View all Cub Cadet Pro Z 160L EFI manuals
Add to My Manuals
Save this manual to your list of manuals |
Cub Cadet Pro Z 160L EFI manual content summary:
- Cub Cadet Pro Z 160L EFI | Owners Manual - Page 1
Rider Pro Z 100 Lapbar Table of Contents Safe Operation Practices 2 Assembly & Set-Up 9 Controls & Operation 11 Service 18 Troubleshooting 25 Replacement Parts 26 Attachments & Accessories 26 Warranties 30 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 2
Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131, Cleveland, Ohio 44136- - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 3
Do not operate the machine while under the influence of operate or service the equipment. Local regulations may alcohol or drugs. further restrict the age and follow all instructions on the Avoid erratic operation and excessive speed. Be aware of machine and in the manual(s) before attempting - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 4
which are not covered in this manual use care and good judgement. Contact your customer service representative for assistance. Slope Operation Children 16 and over should read and understand the instructions and safe operation practices in this manual and on the machine and should be trained and - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 5
2. Use care when loading or unloading machines onto trailers and trucks. 3. If ramps are used, they must be full width, stable, have an adequate capacity rating and be secured to the trailer or truck. Ramp angle should not exceed 15 degrees and trailer or truck should be parked on level terrain. 4. - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 6
this manual. If the safety interlock system does not function properly, have your machine serviced. the engine. 15. Maintain or replace safety and instruction labels, as necessary. 16. Observe proper disposal laws canister. Please contact Customer Support for information regarding the evaporative - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 7
on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING- ROTATING BLADES Do not put hands or feet near rotating parts or under - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 8
Slope Gauge (OK) Figure 1 15° Slope (TOO STEEP) Figure 2 15° Slope 15° dashed line USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 9
problems or questions concerning the machine, phone your local authorized service dealer or contact us directly. We want to ensure your complete satisfaction at all times. Throughout this manual the Drive Control Levers" on page 20 for instructions on the final adjustment of the levers. Figure - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 10
over the positive battery terminal to help protect it from corrosion. NOTE: If the battery is put into service after the date shown on top/side of battery, charge the battery as instructed in "Charging the Battery" on page 22 prior to operating the tractor. Transmission Oil Expansion Reservoir The - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 11
: This Operator's Manual covers several models. Tractor features may vary by model. Not all features in this manual are applicable to be adjusted forward or rearward. Refer to Maintenance & Adjustments section for instructions on using the control levers knobs. T Ignition Switch The ignition - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 12
the engine's charging system is not generating sufficient amperage. Charge the battery as instructed in the Service section of this manual or have the charging system checked by your local service dealer. Air Filter Service The letters "CLN" will display, followed by the letters "AIR", followed by - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 13
key. Wait for all movement to stop before servicing or cleaning. • Operate the drive control levers oil level. Refer to the Engine Operator's Manual for instructions on checking the engine oil level. 7. not operate the tractor. Contact your authorized Cub Cadet Dealer. • The safety interlock system - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 14
cable to the frame of the disabled tractor, as far from the battery as possible. 3. Start the disabled tractor following the normal starting instructions; then disconnect the jumper cables in the exact reverse order of their connection. 4. Have the tractor's electrical system checked and repaired as - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 15
3. Move the throttle control to the FAST position. NOTE: Although the tractor's engine is designed to run at full throttle, when performing a practice session the tractor must be operated at less than full throttle. This only applies to practice. WARNING! Always maintain a firm grip on the control - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 16
2. To turn to the right while traveling in reverse, move the right drive control lever forward of the left lever. See Figure 3-7. Rearward Right Turn Figure 3-7 3. The greater the fore-to-aft distance between the two levers, the sharper the tractor will turn. 4. To execute a "pivot turn," move the - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 17
Using the Mower Deck WARNING! Make certain the area to be mowed is free of debris, sticks, stones, wire or other objects that can be thrown by the rotating blades. NOTE: Do not engage the mower deck when lowered in grass. Premature wear and possible failure of the 'V" belt and PTO clutch will result - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 18
wheel axles with Cub Cadet 251H EP grease after every 10 hours of service. • Periodically lubricate all other pivot points with a quality lubricating oil. Engine Refer to the Engine Operator's Manual for all engine maintenance intervals, procedures, specifications and instructions. Changing the - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 19
has been run flat or seriously under inflated. Have it inspected and serviced by a qualified tire mechanic. Battery Information WARNING! • Should battery transmissions are equipped with a bypass rod that will allow you to manually move the tractor short distances. WARNING! Do not tow the tractor - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 20
problems. 20 Section 4- Service b. Use a fuel stabilizer for storage between 30 and 90 days: • Read the product manufacturer's instructions all fuel in the carburetor has been exhausted. • Referring to the engine manual, drain the fuel from the carburetor bowl. 3. Clean the engine and the - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 21
front auge wheel (b), and adjust the other front gauge wheel (b) into the respective index hole of the other front gauge wheel bracket (e). Figure 4-10 Section 4 - Service 21 - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 22
clothes dryer, etc. 2. Service the engine as instructed in the separate Engine Operator's Manual. 22 Section 4- Service 3. Engines stored between 30 you have a recurring problem with blown fuses, have the tractor's electrical system checked by your Cub Cadet Service Dealer. Relays and Switches - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 23
rolling the belt off the PTO pulley. c. Pull the left side of the belt rearward and downward while manually turning the PTO pulley to the right until the belt rides out onto the edge of the lower sheave of belt routing to make sure that the belt has been routed properly. Section 4 - Service 23 - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 24
switch. Protect your hands by using heavy gloves when handling the blades. When servicing the mower deck, be careful not to cut yourself on the sharpened blades. to change the tractor's transmission drive belt. See your Cub Cadet dealer to have the transmission drive belt replaced. Tractor Creeping - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 25
Troubleshooting Problem Excessive vibration Uneven cut Mower will not mulch grass (If Equipped w/Mulching Kit) Cause 1. Cutting blade loose or unbalanced. 2. Damaged or bent cutting blade. 1. Deck - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 26
Oil Filter Wrench Armortek Non-Stick Spray Carburetor & Choke Cleaner Description Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at www.cubcadet.com. 26 - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 27
Notes 8 27 - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 28
28 Section 8 - Notes - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 29
Section 8 - Notes 29 - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 30
manual problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or at http://support written instructions - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 31
WARRANTED PARTS: The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD Consumer Group Inc demonstrates that the outdoor equipment has been abused, neglected, or improperly maintained, and that such abuse, neglect, - Cub Cadet Pro Z 160L EFI | Owners Manual - Page 32
CUB CADET LLC MANUFACTURER'S LIMITED WARRANTY FOR PRO Z 100 COMMERCIAL ZERO-TURN RIDING MOWERS IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Please see the operator's manual for information on
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
Printed In USA
Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
O
PERATOR
’
S
M
ANUAL
Form No. 769-11036B
(January 19, 2016)
Safe Operation Practices
........................................
2
Assembly & Set-Up
..................................................
9
Controls & Operation
.............................................
11
Service
.....................................................................
18
Troubleshooting
....................................................
25
Replacement Parts
................................................
26
Attachments & Accessories
..................................
26
Warranties
.............................................................
30
Table of Contents
NOTE:
This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all
models and the model depicted may differ from yours.
Zero-Turn Rider
Pro Z 100
Lapbar