Cub Cadet TANK LZ 54 TANK LZ 48 Operator's Manual - Page 14

Connecting the Battery Cables

Get Cub Cadet TANK LZ 54 PDF manuals and user guides View all Cub Cadet TANK LZ 54 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Seat Adjustment This tractor is equipped with an adjustable seat, which includes a retractable seat belt assembly and an Operator Presence Sensor (OPS). The OPS in the form of a switch, is integrated into the seat bottom and is connected to the machine electrical system. The seat can be adjusted forward and back and the arm rest can be adjusted up and down. To move the seat forward or back, locate the seat adjustment rod under the seat. Push the rod to the left and slide the seat forward or back into the desired position and release the rod when the seat is in the desired position. See Fig. 3-9. Connecting the Battery Cables CALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. CAUTION: When attaching battery cables, always connect the POSITIVE (Red) wire to its terminal first, followed by the NEGATIVE (Black) wire. For shipping reasons, both battery cables on your equipment may have been left disconnected from the terminals at the factory. To connect the battery cables, proceed as follows: 1. Using the lever on the back of the seat frame, lift up on the lever and tilt the seat forward. NOTE: The positive battery terminal is marked Pos. (+). The negative battery terminal is marked Neg. (-). NOTE: If the positive battery cable is already attached, skip ahead to step 2. 2. Remove the red boot, if present, from the positive battery terminal and attach the red cable to the positive battery terminal (+) with the bolt and hex nut. See Fig. 3-11. Figure 3-9 To adjust the arm rest, lift the arm rest and rotate the block adjustment into one of the four positions (0-3, 0 being the lowest and 3 being the highest.) and lower the arm rest. See Fig. 3-10. Figure 3-10 14 Section 2- Assembly & Set-Up Figure 3-11 3. Position the red boot over the positive battery terminal to insulate it and help protect it from corrosion. 4. Attach the black cable to the negative battery terminal (-) with the bolt and hex nut. See Fig. 3-11. NOTE: If the battery is put into service after the date shown on top/side of battery, charge the battery prior to operating the tractor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
14
S
ECTION
2— A
SSEMBLY
& S
ET
-U
P
Seat Adjustment
This tractor is equipped with an adjustable seat, which includes a
retractable seat belt assembly and an Operator Presence Sensor
(OPS). The OPS in the form of a switch, is integrated into the seat
bottom and is connected to the machine electrical system.
The seat can be adjusted forward and back and the arm rest can
be adjusted up and down.
To move the seat forward or back, locate the seat adjustment rod
under the seat. Push the rod to the left and slide the seat forward
or back into the desired position and release the rod when the
seat is in the desired position. See Fig. 3-9.
Figure 3-9
To adjust the arm rest, lift the arm rest and rotate the block
adjustment into one of the four positions (0-3, 0 being the lowest
and 3 being the highest.) and lower the arm rest. See Fig. 3-10.
Figure 3-10
Connecting the Battery Cables
CALIFORNIA PROPOSITION 65 WARNING
:
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
CAUTION:
When attaching battery cables, always
connect the POSITIVE (Red) wire to its terminal first,
followed by the NEGATIVE (Black) wire.
For shipping reasons, both battery cables on your equipment
may have been left disconnected from the terminals at the
factory. To connect the battery cables, proceed as follows:
1.
Using the lever on the back of the seat frame, lift up on the
lever and tilt the seat forward.
NOTE:
The positive battery terminal is marked Pos. (+). The
negative battery terminal is marked Neg. (–).
NOTE:
If the positive battery cable is already attached, skip ahead
to step 2.
2.
Remove the red boot, if present, from the positive battery
terminal and attach the red cable to the positive battery
terminal (+) with the bolt and hex nut. See Fig. 3-11.
Figure 3-11
3.
Position the red boot over the positive battery terminal to
insulate it and help protect it from corrosion.
4.
Attach the black cable to the negative battery terminal (–)
with the bolt and hex nut. See Fig. 3-11.
NOTE:
If the battery is put into service after the date shown on
top/side of battery, charge the battery prior to operating the
tractor.