D-Link DCS-1000 Product Manual - Page 72

TCP/IP Properties, Control Panel - replacement

Get D-Link DCS-1000 PDF manuals and user guides View all D-Link DCS-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

need to first disconnect the Internet Camera from the network. Then run the PING utility (follow the instructions in Appendix B - PING Your IP Address.) A2: Another possible reason is the IP Address is located on a different subnet. To fix the problem, run the PING utility (follow the instructions in Appendix B - PING Your IP Address). If the utility returns "no response" or similar, the finding is probably correct, then you should proceed as follows: In Windows 95/98/2000 and Windows NT, check that the IP Address of the Internet Camera is within the same subnet as your workstation. ƒ Click Start, Setting, Control Panel, and the Network icon. ƒ Select TCP/IP from the Network dialog box and from the TCP/IP Properties dialog box click on Specify an IP address. ƒ If the Internet Camera is situated on a different subnet than your workstation, you will not be able to set the IP address from this workstation. To verify make sure the first 3 sections of the IP address of the Internet Camera corresponds to the first 3 sections of the workstation. Therefore the IP address of the Internet Camera must be set from a workstation on the same subnet. A3: Other possible problems might be due to the network cable. Try replacing your network cable. Test the network interface of the product by connecting a local computer to the unit, utilizing a standard Crossover (hub to hub) Cable. If the problem is not solved the Internet Camera might be faulty. Q: Why does the Power LED not light up constantly? A: The power supply used might be at fault. Confirm that you are using the provided power supply, which is DC 5V, for the Internet Camera and verify that the power supply is well connected. Q: Why does the LAN/WLAN LED not light up properly? A1: There might be a problem with the network cable. To confirm that the cables are working, PING the address of a know device on the network. If the cabling is OK and your network is reachable, you should receive a reply similar to the following (...bytes = 32 time = 2 ms). A2: The network device utilized by the Internet Camera is not functioning properly, such as hubs or switches. Confirm the power for the devices are well connected and functioning properly. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
72
need to first disconnect the Internet Camera from the network. Then run the PING utility
(follow the instructions in
Appendix B - PING Your IP Address
.)
A2:
Another possible reason is the IP Address is located on a different subnet. To fix
the problem, run the PING utility (follow the instructions in Appendix B - PING Your IP
Address). If the utility returns “no response” or similar, the finding is probably correct,
then you should proceed as follows:
In Windows 95/98/2000 and Windows NT, check that the IP Address of the Internet
Camera is within the same subnet as your workstation.
Click
Start
,
Setting
,
Control Panel
, and the
Network
icon.
Select TCP/IP from the
Network
dialog box and from the
TCP/IP Properties
dialog box click on
Specify an IP address
.
If the Internet Camera is situated on a different subnet than your workstation, you
will not be able to set the IP address from this workstation. To verify make sure the
first 3 sections of the IP address of the Internet Camera corresponds to the first 3
sections of the workstation. Therefore the IP address of the Internet Camera must
be set from a workstation on the same subnet.
A3:
Other possible problems might be due to the network cable. Try replacing your
network cable. Test the network interface of the product by connecting a local computer
to the unit, utilizing a standard Crossover (hub to hub) Cable. If the problem is not
solved the Internet Camera might be faulty.
Q:
Why does the Power LED not light up constantly?
A:
The power supply used might be at fault. Confirm that you are using the provided
power supply, which is DC 5V, for the Internet Camera and verify that the power supply
is well connected.
Q:
Why does the LAN/WLAN LED not light up properly?
A1:
There might be a problem with the network cable. To confirm that the cables are
working, PING the address of a know device on the network. If the cabling is OK and
your network is reachable, you should receive a reply similar to the following (…bytes
= 32 time = 2 ms).
A2:
The network device utilized by the Internet Camera is not functioning properly,
such as hubs or switches. Confirm the power for the devices are well connected and
functioning properly.