D-Link DCS-2132L User Manual - Page 31

Static IP Client, IP Address, Subnet Mask, Default Gateway, Enable PPPoE, User Name, Password - setup

Get D-Link DCS-2132L PDF manuals and user guides View all D-Link DCS-2132L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Section 4: Configuration Internet Connection Setup Wizard The Internet Connection Setup Wizard will guide you through a step-by-step process to configure your DCS-2132L and connect your IP camera to the Internet. Note: Use this wizard if you are connecting the camera directly to a public IP address. If you are connecting the camera to a router, select DHCP (most common). Select Static IP to manually assign the camera its IP settings. Click Next to continue. Select DHCP (Dynamic Host Configuration Protocol) if you want your DHCP server (usually enabled on your router) to assign the camera its IP settings. If you want to manually assign the IP settings, select Static IP Client and enter the following details from your Internet Service Provider (ISP): IP Address: Enter an IP Address for your camera. Subnet Mask: Enter the Subnet Mask of your network. Default Router: Enter the Default Gateway address. This is usually the IP address (LAN) of your router. Primary DNS: Enter the primary DNS server's IP address. This is usually also the IP address (LAN) of your router. Secondary Enter the secondary DNS server's IP address. This is optional. DNS: If you are required to connect using PPPoE (Point to Point Protocol over Ethernet), check the box to Enable PPPoE and enter the User Name and Password for your PPPoE connection. Only select this option if your camera is directly connected to your broadband modem. If it is on a network with a router or gateway, do not select this option. Click Next to continue. D-Link DCS-2132L User Manual 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
31
D-Link DCS-2132L User Manual
Section 4: Configuration
Internet Connection Setup Wizard
The
Internet Connection Setup Wizard
will guide you through a step-by-step
process to configure your DCS-2132L and connect your IP camera to the Internet.
Note:
Use this wizard if you are connecting the camera directly to a public IP
address. If you are connecting the camera to a router, select DHCP (most common).
Select Static IP to manually assign the camera its IP settings.
Click
Next
to continue.
Select
DHCP
(Dynamic Host Configuration Protocol) if you want your DHCP server
(usually enabled on your router) to assign the camera its IP settings.
If you want to manually assign the IP settings, select
Static IP Client
and enter
the following details from your Internet Service Provider (ISP):
Enter an
IP Address
for your camera.
Enter the
Subnet Mask
of your network.
Enter the
Default Gateway
address. This is usually the IP
address (LAN) of your router.
Enter the primary DNS server’s IP address. This is usually also
the IP address (LAN) of your router.
Enter the secondary DNS server’s IP address. This is optional.
IP Address:
Subnet Mask:
Default Router:
Primary DNS:
Secondary
DNS:
If you are required to connect using PPPoE (Point to Point Protocol over Ethernet),
check the box to
Enable PPPoE
and enter the
User Name
and
Password
for your
PPPoE connection. Only select this option if your camera is directly connected
to your broadband modem. If it is on a network with a router or gateway, do
not select this option.
Click
Next
to continue.