D-Link DSN-2100-10 User's Manual for DSN-2100-10 Valid for firmware - Page 143

C.2.3, Setting the Out-of-Band Port Configuration

Get D-Link DSN-2100-10 - xStack Storage Area Network Array Hard Drive PDF manuals and user guides
UPC - 790069310638
View all D-Link DSN-2100-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 143 highlights

C.2.3 Setting the Out-of-Band Port Configuration To set the xStack Storage Array out-of-band configuration, use the following procedure: 1. From the management port diagnostic menu, type 3 and press Enter. The current xStack Storage Array IP address, subnet mask, gateway, and hostname are displayed (see Figure C-7) and you are prompted to enter a new IP address for the management port. Figure C-7. Example of xStack Storage Array Settings 2. To keep the current IP address for the management port, press Enter. Otherwise, enter a new address and press Enter. You are prompted for a subnet mask. 3. To keep the current subnet mask for the management port, press Enter. Otherwise, enter a new subnet mask and press Enter. You are prompted for a gateway. 4. To keep the current gateway, press Enter. Otherwise, enter a new gateway and press Enter. You are prompted for a hostname. 5. To keep the current hostname, press Enter. Otherwise, enter a new hostname and press Enter. A message says you must reboot the xStack Storage Array for the new settings to take effect, and then asks whether you want to change the management port IP address. 6. To reset the management port IP address, type y. Otherwise, type n. If you typed y, the new management port settings take effect the next time the xStack Storage Array restarts. xStack Storage User's Guide 143

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
xStack Storage User’s Guide
143
C.2.3
Setting the Out-of-Band Port Configuration
To set the xStack Storage Array out-of-band configuration, use the following procedure:
1.
From the management port diagnostic menu, type
3
and press Enter. The current xStack
Storage Array IP address, subnet mask, gateway, and hostname are displayed (see Figure
C-7) and you are prompted to enter a new IP address for the management port.
Figure C-7. Example of xStack Storage Array Settings
2.
To keep the current IP address for the management port, press Enter. Otherwise, enter
a new address and press Enter. You are prompted for a subnet mask.
3.
To keep the current subnet mask for the management port, press Enter. Otherwise,
enter a new subnet mask and press Enter. You are prompted for a gateway.
4.
To keep the current gateway, press Enter. Otherwise, enter a new gateway and press
Enter. You are prompted for a hostname.
5.
To keep the current hostname, press Enter. Otherwise, enter a new hostname and press
Enter. A message says you must reboot the xStack Storage Array for the new settings to
take effect, and then asks whether you want to change the management port IP address.
6.
To reset the management port IP address, type
y
. Otherwise, type
n
. If you typed
y
, the
new management port settings take effect the next time the xStack Storage Array
restarts.