D-Link DSN-2100-10 User's Manual for DSN-2100-10 Valid for firmware - Page 35

Starting the xStack Storage Array for the First Time

Get D-Link DSN-2100-10 - xStack Storage Area Network Array Hard Drive PDF manuals and user guides
UPC - 790069310638
View all D-Link DSN-2100-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Chapter 4 Starting the xStack Storage Array for the First Time The xStack Storage Array is designed with simplicity and ease-of-use in mind for new users. Towards that end, the xStack Storage Array comes with an "Out-Of-Box Experience" (OOBE) setup wizard that lets you expedite the unit's configuration. After the OOBE setup wizard is completed, the xStack Storage Array boots up using the settings you configured in the OOBE setup wizard. Thereafter, you can use the procedures in Chapter 5 to change these settings if necessary. Before you start the OOBE: 1. Connect a PC with an installed Web browser. The IP address for the NIC in the management PC must be on the same IP subnet (192.168.1.x) as the management port. 2. Start a Web browser on the PC connected to the xStack Storage Array's management port. 3. In the browser's address bar, type the following default IP address for the management console and press the Enter key: 192.168.1.1 4. Start the xStack Storage Array and proceed to Section 4.1. 4.1 Initial Startup and Welcome When you start the xStack Storage Array for the first time, the system goes through its Power On Self Test, and then displays the Welcome screen shown in Figure 4-1. Click the Start button in the Welcome screen to continue and proceed to Section 4.2. Figure 4-1 Welcome Screen xStack Storage User's Guide 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
xStack Storage User’s Guide
35
Chapter 4
Starting the xStack Storage Array for the First Time
The xStack Storage Array is designed with simplicity and ease-of-use in mind for new users.
Towards that end, the xStack Storage Array comes with an "Out-Of-Box Experience" (OOBE) setup
wizard that lets you expedite the unit’s configuration.
After the OOBE setup wizard is
completed, the xStack Storage Array boots up using the settings you configured in the OOBE
setup wizard.
Thereafter, you can use the procedures in Chapter 5 to change these settings if
necessary.
Before you start the OOBE:
1.
Connect a PC with an installed Web browser.
The IP address for the NIC in the management PC must be on the same IP
subnet (192.168.1.x) as the management port.
2.
Start a Web browser on the PC connected to the xStack Storage Array’s management port.
3.
In the browser’s address bar, type the following default IP address for the management
console and press the Enter key:
192.168.1.1
4.
Start the xStack Storage Array and proceed to Section 4.1.
4.1
Initial Startup and Welcome
When you start the xStack Storage Array for the first time, the system goes through its Power On
Self Test, and then displays the Welcome screen shown in Figure 4-1. Click the
Start
button in
the Welcome screen to continue and proceed to Section 4.2.
Figure 4-1 Welcome Screen