D-Link DSN-2100-10 User's Manual for DSN-2100-10 Valid for firmware - Page 94

Changing Initial Configuration Settings, Changing the Out-of-Band Port Configuration

Get D-Link DSN-2100-10 - xStack Storage Area Network Array Hard Drive PDF manuals and user guides
UPC - 790069310638
View all D-Link DSN-2100-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

5.5 Changing Initial Configuration Settings When you started the xStack Storage Array for the first time, you specified the unit's initial settings using the OOBE setup wizard. You may need to change these settings in the future. For example, you may need to change the date and time if time changes occur in your area. The following sections describe how to change the settings you specified during the OOBE setup wizard. 5.5.1 Changing the Out-of-Band Port Configuration You specified the management interface settings in the OOBE setup wizard when you started the xStack Storage Array for the first time. If you need to change these settings, perform the following procedure: 1. Click the xStack Storage icon on the Physical Resources tab. 2. Perform one of the following steps: - On the File menu, click Configure Out of Band Port. - Right-click and click Configure Out of Band Port. Either step displays the Configure Out of Band Port dialog box (see Figure 5-46). Figure 5-46 Configure Out of Band Port Dialog Box 3. Complete the fields in the dialog box (see Table 5-19). For convenience, the current settings appear below each field. Remember the new IP address; you will need it for subsequent logins to the console. We recommend that you record the IP address in Appendix B. 4. On the File menu, click Restart. When the confirmation prompt "Do you want to restart the system?" appears, click Yes. 94 Chapter 5 Configuring the xStack Storage Array

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
94
Chapter 5
Configuring
the xStack Storage Array
5.5
Changing Initial Configuration Settings
When you started the xStack Storage Array for the first time, you specified the unit’s initial
settings using the OOBE setup wizard. You may need to change these settings in the future. For
example, you may need to change the date and time if time changes occur in your area.
The following sections describe how to change the settings you specified during the OOBE setup
wizard.
5.5.1
Changing the Out-of-Band Port Configuration
You specified the management interface settings in the OOBE setup wizard when you started the
xStack Storage Array for the first time. If you need to change these settings, perform the
following procedure:
1.
Click the
xStack Storage
icon on the
Physical Resources
tab.
2.
Perform one of the following steps:
–
On the
File
menu, click
Configure Out of Band Port
.
–
Right-click and click
Configure Out of Band Port
.
Either step displays the Configure Out of Band Port dialog box (see Figure 5-46).
Figure 5-46 Configure Out of Band Port Dialog Box
3.
Complete the fields in the dialog box (see Table 5-19).
For convenience, the current settings appear below each field. Remember
the new IP address; you will need it for subsequent logins to the console. We
recommend that you record the IP address in Appendix B.
4.
On the
File
menu, click
Restart
. When the confirmation prompt “
Do you want to restart the
system?
” appears, click
Yes
.