Denon 589BA Owners Manual - Page 34

Getting Started Connections Setup Playback Remote Control Information Troubleshooting Specifications ENGLISH A2 SW ATT (Subwoofer Attenuation) Attenuate subwoofer level when using EXT. IN mode. [Selectable items] ON : The input from the subwoofer channel is attenuated. OFF : The input from the subwoofer channel is not attenuated. Usually use in this mode. Set this to "ON" if the subwoofer channel level seems too high when playing audio signal. A3 Subwoofer Turn subwoofer output on and off. [Selectable items] ON : The subwoofer is used. OFF : The subwoofer is not used. A4 Tone Control Turn tone adjustments on and off. [Selectable items] ON : A llow tone adjustment (treble, bass). OFF : Playback without tone adjustment. The tone cannot be adjusted when in the DIRECT mode. NOTE When the "Dynamic EQ" setting is "ON", setting is not possible. A5 Bass Adjust low frequency range (bass). [Variable range] -6dB ~ 0dB ~ +6dB A6 Treble Adjust high frequency range (treble). [Variable range] -6dB ~ 0dB ~ +6 dB A7 MultEQ Select the type of room correction desired from the following list: [Selectable items] Audyssey : Optimize frequency response of all speakers. Byp. L/R : Optimize frequency response of speakers except front L and R speakers. Flat : Optimize frequency response of all speakers to flat response. OFF : Turn equalizer off. Audyssey Audyssey Byp. L/R OFF Audyssey Flat Operating from the main unit or remote control unit Press MULTEQ. • When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, the Audyssey MultEQ indicator lights green. • After running Auto Setup, if the Speaker Configuration, Distance, Channel Level and Crossover Frequency have changed without increasing the number of speakers measured, the Audyssey MultEQ indicator lights red. NOTE • "MultEQ" can only be set when Auto Setup has been performed. • "MultEQ" cannot be set in the following situations. • If "Auto Setup" fails to be completed. • After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. • If the settings of speakers for which "None" has been determined at "Auto Setup" are changed, "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" cannot be selected. Either perform Auto Setup again, or return to the setting after running Auto Setup with "System Setup" - "Speaker Setup" - "Restore". • When using headphones, "MultEQ" is set to "OFF". A8 Dynamic EQ Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to provide well-balanced sound for every listener at any volume level. NOTE • " Dynamic EQ" can only be set when auto setup has been performed. • " Dynamic EQ" cannot be set in the following situations. • If "Auto Setup" fails to be completed. • After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. • W hen "MultEQ" is set to "OFF", "Dynamic EQ" is automatically set to "OFF". • " Night Mode" and "Tone Control" cannot be used jointly. [Selectable items] ON : Use Dynamic EQ function. OFF : Do not use Dynamic EQ function. Operating from the unit or remote control unit Press or [DYNAMIC VOLUME]. Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF Dynamic EQ / Volume : OFF Before running Auto Setup and after running Auto Setup, if the number of speakers has increased or you pressed or [DYNAMIC VOLUME], "Run Audyssey" is displayed. In this case, either perform Auto Setup again, or return to the setting after running Auto Setup with "System Setup" - "Speaker Setup" - "Restore". n Operating conditions for each function • D ynamic EQ : When "MultEQ" is set to "ON" • D ynamic Volume : When "Dynamic EQ" is set to "ON" • D V setting : When "Dynamic Volume" is set to "ON" A7 MultEQ A8 Dynamic EQ A9 Dynamic Volume S0 DV Setting "Bass" and "Treble" can be set when "Tone Control" is set to "ON". 31 For details on adjusting individual parameters, see "Adjusting the Parameters" (vpage 29).