Denon DN X100 Operating Instructions - Page 7

Connections - power cords

Page 7 highlights

3 CONNECTIONS Refer to the connection diagram below. 1. Make certain AC power is off while making connections. 2. Quality cables make a big difference in fidelity and punch. Use high-quality, audio cables. 3. Do not use excessively long cables. Be sure plugs and jacks are securely fastened. Loose connections cause hum, noise, or intermittents that could damage your speakers. 4. Connect all stereo input sources. Then connect any effects into the stereo effect, if used. Connect your microphone(s) and monitor headphones. Make sure all faders are at "zero" and the unit is off. Take care to connect only one cable at a time. Pay attention to L and R position of jacks, on both the DN-X100 and outboard gear. 5. Connect the stereo outputs to the power amplifier(s) and/or tape deck(s) and/or MD recorder(s) and/or CD recorder(s). Plug the DN-X100 into AC power outlet. NOTE: Always switch on your audio input sources such as CD players first, then your mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input units. CD player POWER ON OFF TITLE MEMO PRESET TIME CONT. /SINGLE TAP ECHO /LOOP FLANGER AUTO FILTER DISC MODE ON : SCRATCH OFF : SEARCH/ BEND DRAG-S BRAKE RVS TITLE CUE CUE/STUTTER PLAY/PAUSE DISC EJECT BPM FLIP CLR NEXT TR. /B TRIM A1 A2 A PARAMETERS PUSH B EXIT/ RELOOP QUICK JUMP TRACK SEARCH MP3 SEARCH MODE FAST SEARCH 0 PITCH/KEY RANGE PITCH BEND CD player POWER ON OFF TITLE MEMO PRESET TIME CONT. /SINGLE TAP ECHO /LOOP FLANGER AUTO FILTER DISC MODE ON : SCRATCH OFF : SEARCH/ BEND DRAG-S BRAKE RVS TITLE CUE CUE/STUTTER PLAY/PAUSE DISC EJECT BPM FLIP CLR NEXT TR. /B TRIM A1 A2 A PARAMETERS PUSH B EXIT/ RELOOP QUICK JUMP TRACK SEARCH MP3 SEARCH MODE FAST SEARCH 0 PITCH/KEY RANGE PITCH BEND Turntable 2 43 210 4 SLOW BRAKE OFF ON POWER START /STOP 78 33 45 KATING 0 KEY ADJUST PITCH -12 Quartz 0 +12 DP-DJ151 Digital 765 765 Turntable 1 43 210 4 SLOW BRAKE OFF ON POWER START /STOP 78 33 45 KATING 0 KEY ADJUST PITCH -12 Quartz 0 +12 DP-DJ151 Digital Balanced microphone ENGLISH ANTI-S 1 3 2 ANTI-S 1 3 2 1/4" TRS mono jack 1/4" TRS jack L R DN-X100 RL LR RL LR 3.5 mm stereo mini cord 3.5 mm stereo mini cord To power outlet Main balanced power amplifier AA-26: for AC 120V AA-27: for AC 230V AA-26 or AA-27 AC ADAPTOR Note: Use specified attached AC adaptor only. RL Main unbalanced power amplifier 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17

DN-X100
R
L
L
R
R
L
R
L
R
L
R
L
ON
CUE/STUTTER
CUE
PLAY/PAUSE
POWER
:
OFF
DRAG-S
BRAKE
ON
:
TAP
PRESET
CONT.
TIME
/SINGLE
MEMO
MP3 SEARCH MODE
TITLE
RVS
ECHO
/LOOP
DISC MODE
FILTER
FLANGER
PITCH/KEY
RANGE
PITCH BEND
0
OFF
A1
RELOOP
EXIT/
B
A2
PARAMETERS
PUSH
TRACK SEARCH
NEXT TR.
/B TRIM
CLR
A
FLIP
FAST SEARCH
SEARCH/
BEND
SCRATCH
AUTO
DISC EJECT
ON
CUE/STUTTER
CUE
PLAY/PAUSE
POWER
:
OFF
DRAG-S
BRAKE
ON
:
TAP
PRESET
CONT.
TIME
/SINGLE
MEMO
MP3 SEARCH MODE
TITLE
RVS
ECHO
/LOOP
DISC MODE
FILTER
FLANGER
PITCH/KEY
RANGE
PITCH BEND
0
OFF
A1
RELOOP
EXIT/
B
A2
PARAMETERS
PUSH
TRACK SEARCH
NEXT TR.
/B TRIM
CLR
A
FLIP
FAST SEARCH
SEARCH/
BEND
SCRATCH
AUTO
DISC EJECT
7
ENGLISH
3
CONNECTIONS
Refer to the connection diagram below.
1. Make certain AC power is off while making
connections.
2. Quality cables make a big difference in fidelity and
punch. Use high-quality, audio cables.
3. Do not use excessively long cables. Be sure plugs
and jacks are securely fastened. Loose connections
cause hum, noise, or intermittents that could
damage your speakers.
4. Connect all stereo input sources. Then connect any
effects into the stereo effect, if used. Connect your
microphone(s) and monitor headphones. Make sure
all faders are at “zero” and the unit is off. Take care
to connect only one cable at a time. Pay attention to
L and R position of jacks, on both the DN-X100 and
outboard gear.
5. Connect the stereo outputs to the power
amplifier(s) and/or tape deck(s) and/or MD
recorder(s) and/or CD recorder(s). Plug the DN-X100
into AC power outlet.
Turntable 2
Main unbalanced power amplifier
Main balanced power amplifier
1/4” TRS
mono jack
NOTE:
Always switch on your audio input sources such as
CD players first, then your mixer, and finally any
amplifiers. When turning off, always reverse this
operation by turning off amplifiers, then your mixer,
and then input units.
Turntable 1
3.5 mm stereo mini cord
3.5 mm stereo mini cord
Balanced microphone
CD player
1/4” TRS jack
AC ADAPTOR
To power outlet
CD player
Note:
Use specified attached AC
adaptor only.
AA-26: for AC 120V
AA-27: for AC 230V
AA-26
or
AA-27